Related Manuals for Pentair HYDROMATIC HPS4SC
Summary of Contents for Pentair HYDROMATIC HPS4SC
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP HPS3SC(X), HPS4SC(X) , HPS4HC(X), HPS6MC(X) INSTALLATION & OPERATION MANUAL pentair.com/hydromatic ©2025 Pentair. All Rights Reserved.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 GENERAL INFORMATION . -
Page 3: Safety Information
SAFETY INFORMATION SAFETY SYMBOLS CUTTING RISK. Risk of serious cutting or amputation exists. Use caution as liner plate is extremely This is the safety alert symbol. When you see this symbol sharp. Always keep fingers and hands away from cutting on your pump or in this manual, look for one of the following profiles. -
Page 4: General Information
GENERAL INFORMATION This manual contains important safety information regarding HEAT SENSORS the use of this product. This product should only be installed All motors in this family have heat sensors on or embedded in the and serviced by a qualified professional. Carefully read and motor winding to detect excessive heat. -
Page 5: Installation
INSTALLATION MAKING ELECTRICAL CONNECTIONS TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE Only a 230V pump from the factory is considered dual voltage, ElECTROCUTION HAZARD: Must be a cord label clearly states the factory wound voltage. installed by a qualified professional. Disconnect all electrical power before installation or servicing the pump. -
Page 6: Operation / Maintenance
OPERATIONS & MAINTENANCE PUMP MAINTENANCE RISK OF FIRE OR EXPLOSION. Do not smoke or use open flames in or around this system. Only the FM listed As the motors are oil filled, no lubrication or other maintenance products are to be used in a hazardous location applications per is required. - Page 7 CONFIDENTIAL contains trade secrets and [XXX] DIMENSIONS IN mm materials, compounds and other similar criteria are to be other proprietary information of Pentair CRITICAL DIMENSIONS THAT NEED Water. Duplication, disclosure or use are strictly adhered to. No modifications allowed without TO BE INSPECTED.
-
Page 8: Troubleshooting
Check in sump to be sure control is free. Selector switch may be in the Hand position. IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION, OPERATION, MAINTENANCE OR TROUBLESHOOTING OF THE PUMP, PLEASE CALL PENTAIR AT 855-274-8947. E-03-600 / 056255641 (03-28-25) - Page 9 NOTES PAGE E-03-600 / 056255641 (03-28-25)
-
Page 10: Parts List
PARTS LIST HPS3SC(X), HPS4SC(X), HPS4HC(X), HPS6MC(X) For use with product built with Premium Efficient motor. 4HC / 6MC 3SC / 4SC E-03-600 / 056255641 (03-28-25) -
Page 11: Part Description
PARTS LIST ITEM PART DESCRIPTION PART # 3SC / 4SC 4HC / 6MC CORD CAP 10-4 35' 152880315 CORD CAP 8-4 35' 152880325 CORD CAP 6-4 35' 152880355 STATOR SEE MOTOR PARTS GROUP ROTOR/SHAFT SEE MOTOR PARTS GROUP STATOR BOLT SHCS SEE MOTOR PARTS GROUP STATOR SPACER 007362141... - Page 12 PARTS LIST HYDRAULIC ENDS B2 F26 B14 F26 B2 F26 B9 F26 B2 F26 B9 F26 TYPICAL: GAP BETWEEN LINER(B17) AND IMPELLER(1) TO BE SET AT .008-.015" FROM FACTORY ITEM DESCRIPTION KEY 3/8 X 1/4 SHAFT TO IMP ** / ++ 083460011 083460011 083460011...
-
Page 13: Motor Parts
PARTS LIST MOTOR PARTS 15 HP 15/20/23 HP 15/20/23 HP ITEM 2-POLE 3450RPM 208/3/60 230/460/3/60 575/3/60 STATOR 27889D003 27889D003 27889D603 ROTOR/SHAFT ASSEMBLY 27887D015 27887D015 27887D015 BOLT-STATOR (4) 001780051 001780051 001780051 SPACER 007362141 007362141 007362141 OIL-TRANSFORMER (1 .69) 153620017 153620017 153620017 10/15/20 HP 10/15/20/23 HP 10/15/20/23 HP... - Page 14 PARTS LIST IMPELLER PARTS LIST - HPS4SC (X) - 3450 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER # 528800217 5 .88" 154371132 HPS4SCP015203 208/3 528800227 5 .88" 154371132 HPS4SCP015223 230/460/3 528800237 5 .88" 154371132 HPS4SCP015243 460/3 528800247 5 .88" 154371132 HPS4SCP015253 575/3...
- Page 15 PARTS LIST IMPELLER PARTS LIST - HPS6MC(X) - 1750 RPM DESCRIPTION PART # VOLTAGE/PH CORD TRIM IMPELLER HPS6MCP015403 528610217 208/3 8 .75" 154421102 HPS6MCP015423 528610227 230/460/3 8 .75" 154421102 HPS6MCP015443 528610237 460/3 8 .75" 154421102 HPS6MCP015453 528610247 575/3 10-4 8 .75" 154421102 HPS6MCXP015403 528616217...
-
Page 16: Wiring Diagrams
WIRING DIAGRAMS E-03-600 / 056255641 (03-28-25) - Page 17 WIRING DIAGRAMS E-03-600 / 056255641 (03-28-25)
-
Page 18: Standard Limited Warranty
Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility. - Page 19 NOTES PAGE E-03-600 / 056255641 (03-28-25)
- Page 20 Loctite® is a registered trademark of Henkel AG & Company KGaA . All indicated Pentair trademarks and logos are property of Pentair . Third party registered and unregistered trademarks and logos are the property of their respective owners . ©2025 Pentair . All Rights Reserved .
Need help?
Do you have a question about the HYDROMATIC HPS4SC and is the answer not in the manual?
Questions and answers