Related Manuals for GEA ECOVENT TEFASEP-Gold ECO E
Summary of Contents for GEA ECOVENT TEFASEP-Gold ECO E
- Page 1 Hygienic valves ® GEA ECOVENT accessories - angle seat valve_TEFASEP-Gold Assembling Instruction (Translation from the original language) 221BAL015386EN_1...
- Page 2 EU Machinery Directive. This document is protected by copyright. All rights reserved. The document may not, in whole or in part, be copied, reproduced, translated or reduced to an electronic medium of machine-readable form without the express permission of GEA Tuchenhagen GmbH.
-
Page 3: Table Of Contents
TABLE OF CONTENTS General Information Information about this document Safety Intended use Technical data Technical data Tightening torques for the hinged clamps/ cast C-rings Tefasep Gold Note Servicing intervals Exchanging the O-ring (TEFASEP gold) Spare parts list - angle seat valve ECO NI Dimension sheet - angle seat valve_ECO E 221BAL015386EN_1 01.11.2023... - Page 4 221BAL015386EN_1 01.11.2023...
-
Page 5: General Information
General Information Information about this document General Information Information about this document These additional operating instructions are part of the user information for the valve. These additional operating instructions contain the manufacturer's instructions to the operator of the valve and to all persons who work on or use the valve regarding the procedures to follow. They include basic instructions for use of the valves. -
Page 6: Safety
Safety Intended use Safety Intended use The valve is used for opening and closing pipeline sections. Proper use of the valve also includes compliance with these operating instructions. The medium should preferably flow in the opening direction of the valve disk to avoid pipe hammers when the valve is opened or closed. -
Page 7: Technical Data
Technical data Technical data Technical data Technical data Refer to the following tables for the key technical data of the valve: Technical data: Valve Designation Description Size 4" to 6" OD Material of product contact parts Stainless steel 1.4404 Any position, if valve and pipe system can drain Fitting position properly Technical data: Ambient temperatures... -
Page 8: Tightening Torques For The Hinged Clamps/ Cast C-Rings
Technical data Tightening torques for the hinged clamps/ cast C-rings Technical data: Compressed air supply, product pressure Designation Description 6 bar (87 psi), max. 8 bar (116 psi) configuration with standard drive Control air pressure Alternative combinations of product pressure and control air pressure on request 2 bar (30 psi) configuration with standard Product pressure... -
Page 9: Tefasep Gold Note
Tefasep Gold Note Tefasep Gold Note Hint! TEFASEP gold valve seat seals achieve optimal sealing only after an initial CIP or SIP cleaning. CIP or SIP cleaning operating conditions: -Medium: lye, hot water or saturated steam - Temperature: >80 °C (176 °F) - Hold time: 20 …... -
Page 10: Servicing Intervals
Tefasep Gold Servicing intervals Servicing intervals To ensure the highest operational reliability, all wearing parts should be replaced at longer intervals. The actual servicing intervals can only be determined by the user since they depend on the operating conditions, for instance: •... -
Page 11: Exchanging The O-Ring (Tefasep Gold)
Tefasep Gold Exchanging the O-ring (TEFASEP gold) Exchanging the O-ring (TEFASEP gold) Tools required: • O-ring cutter • Heat-resistant protective gloves • Oven (no microwave) Caution! Health hazard due to toxic fumes! The O-ring cutter cuts the seal with a hot metal tip. At temperatures of more than 300 °C, toxic fumes can be released. - Page 12 Tefasep Gold Fig.3 Use both thumbs to press the heated O-ring (TEFASEP gold valve seat seal) into the radial groove at one point. Fig.4 Then use both palms to press the valve seat seal in place in the radial groove. ! Make sure the valve seat seal "clicks"...
-
Page 13: Spare Parts List - Angle Seat Valve Eco Ni
Spare parts list - angle seat valve ECO NI Spare parts list - angle seat valve ECO NI Fig.6 221BAL015386EN_1 01.11.2023... - Page 14 Spare parts list - angle seat valve ECO NI Item Designation Material 4" OD 6" OD Seal ring EPDM 924-085 924-085 924-083 924-083 Bearing PTFE/carbon 935-088 935-003 Bearing, 3A PEEK450G 935-100 935-102 Seal disk 1.4404 221-141.15 221-141.66 Locking ring 1.4301 221-641.04 221-641.05 O-ring...
-
Page 15: Dimension Sheet - Angle Seat Valve_Eco E
Dimension sheet - angle seat valve_ECO E Dimension sheet - angle seat valve_ECO E Fig.7 221BAL015386EN_1 01.11.2023... - Page 16 Dimension sheet - angle seat valve_ECO E Dimension 4'' OD 6'' OD [mm] [mm] 1105 Ø 101.6 x 2.1 152.4 x 2.7 [mm] [mm] 79.5 118.5 Stroke S [mm] Weight [kg] 40.0 59.6 221BAL015386EN_1 01.11.2023...
- Page 17 Dimension sheet - angle seat valve_ECO E 221BAL015386EN_1 01.11.2023...