Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sumake EMC-B40H
Summary of Contents for Sumake EMC-B40H
- Page 1 INSTRUCTION MANUAL EMC-B40H, EMC-B40HA ITEM NO.: ELECTRIC SANDER,CENTRAL-VACUUM 3MM ORBITAL W/ 3"*4"HOOK PAD EMN-B40H, EMN-B40HA ITEM NO.: ELECTRIC SANDER, NON-VACUUM 3MM ORBITAL W/ 3"*4"HOOK PAD *E-type* EMC(N)-B40-I-2007B-X2...
-
Page 2: Important Safeguards
It should only be used for such sanding applications and within marked capacity and ratings. Only accessories specifically recommended by SUMAKE should be used with this tool. Use in any other manner or with other accessories could lead to unsafe operating conditions. - Page 3 b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Page 4 and inspect for worn or damaged components. Correct or replace the suspect component. If abnormal noise or vibration still exists, return the tool to SUMAKE for repair or replacement. Refer to warranty instructions. Prior to use, inspect abrasive product and accessories for possible damage. If damaged, replace with ...
-
Page 5: Specification
(r.p.m.) inch Central EMC-B40HA 75x100 7.32 2.47 1.12 Vacuum 110-120VAC 50-60HZ EMN-B40HA 75x100 8.64 2.58 1.17 4,000 Vacuum 350W Max 7,000 Central 150W Rated EMC-B40H 9,000 75x100 7.32 2.47 1.12 Vacuum 220-240VAC 50-60HZ EMN-B40H 75x100 8.64 2.58 1.17 Vacuum... - Page 6 OPERATING INSTRUCTIONS PRIOR TO THE OPERATION The tool is intended to be operated as a hand held tool. It is always recommended that while using the tool, operators stand on a solid floor, in a secure position with a firm grip and footing. Be aware that the sander can develop a torque reaction.
- Page 7 MAXIMUM SPEED AND INTERMEDIATE SPEED CONTROL 1. Maximum Speed is adjusted by pressing the “+” or “-” buttons on the buttrons plate of the Sander. Each touch will raise or lower the speed to the next setting. 2. Intermediate speeds between Zero (0)/min (RPM) and the set Maximum Speed can be used with intermediate Lever positions.- see figure 4.
-
Page 8: Health And Safety Information
fully cooled down. Once the PCB has fully cooled, it will turn back into a flashing green light. The tool can then resume operation by pressing the lever again. CLEANING 1. Periodically blow out all air passages and area above Disk Pad and under shroud with dry compressed air. - Page 9 NOTE www.SUMAKE.com www.AIRCOMPRESSOR.com.tw...
-
Page 10: Eu Declaration Of Conformity (Doc)
EU Declaration of Conformity (DOC) SUMAKE INDUSTRIAL CO., LTD. 4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan declare in sole responsibility that the equipment Equipment： ELECTRIC ORBITAL SANDER Model/ Serial No.： EMC-B40H The object of the declaration described above is in conformity with the relevant union harmonization legislation: ... - Page 11 EU Declaration of Conformity (DOC) SUMAKE INDUSTRIAL CO., LTD. 4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan declare in sole responsibility that the equipment Equipment： ELECTRIC ORBITAL SANDER Model/ Serial No.： EMN-B40H The object of the declaration described above is in conformity with the relevant union harmonization legislation: ...
- Page 12 EMC-B40H, EMC-B40HA ELECTRIC SANDER, CENTRAL-VACUUM 3MM ORBITAL W/ 3"*4"HOOK PAD EMN-B40H, EMN-B40HA ELECTRIC SANDER, NON-VACUUM 3MM ORBITAL W/ 3"*4"HOOK PAD EMC(N)-B40-P-2308E-X2...
-
Page 13: Parts List
XPA0080 Spacer(0.4T) XPA0079 Spacer(0.2T) EOS32013 Grip EOS40029 Lever for SUMAKE 9,000 OPM e-ROS (1/8") Orbit (220-240V) (For EMC-B40H, EMN-B40H) Lever for SUMAKE 9,000 OPM e-ROS (1/8") Orbit (110-120V) (For EMC-B40HA, EMN-B40HA) EOS30042 Valve Stem Assembly EOS50102 Dust Cover EOS50129 Spring... -
Page 14: Troubleshooting Guide
Troubleshooting Guide Symptom Solution The sander has started automatically and cannot be Re-programing the tool stopped after plugged in Re-programing the tool The sander doesn’t work after Replace PCB Check PCB controller plugged in lights Replace the Motor The sander work with abnormal Replace Motor sound from motor The sander work with abnormal... - Page 15 Electric sander quality issue check SOP Please provide warranty principle and check list to customer. Please try to re-set and check if sander problem could be eliminated. Please refer SUMAKE service center media category. http://www.sumake-service-center.com/media.php?cid=13&page=2 If problem could not be eliminated after re-set, please ask customer to provide information per check list.
- Page 16 Electric Sander Check List 1. Serial number of sander or sander model or motor serial number: 2. Material of work-piece or application, with picture if possible: 3. Number of sanding paper (#), with picture if possible: 4. Use sander with vacuum cleaner: □ Yes □ No 5.
Need help?
Do you have a question about the EMC-B40H and is the answer not in the manual?
Questions and answers