Sumake ELSC-50H(V) Instruction Manual
  1. Manuals
  2. Brands
  3. Sumake Manuals
  4. Sander
  5. ELSC-50H(V)
  6. Instruction manual

Sumake ELSC-50H(V) Instruction Manual

Sander/polisher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ITEM NO.:
2 IN 1 ELECTRIC CENTRAL-VACUUM SANDER/POLISHER
ITEM NO.:
2 IN 1 ELECTRIC CENTRAL-VACUUM SANDER/POLISHER
ITEM NO.:
2 IN 1 ELECTRIC NON-VACUUM SANDER/POLISHER
INSTRUCTION MANUAL
ELSC-50H(V), ELSC-60H(V)
W/5"(6") HOOK (VINYL) PAD
ELSC-50HM, ELSC-60HM
W/5"(6") MULTIHOLE HOOK (VINYL) PAD
ELSN-50H(V), ELSN-60H(V)
W/5"(6") HOOK (VINYL) PAD
ELSC(N)-B50(60)-I-1604A-X2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ELSC-50H(V) and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sumake ELSC-50H(V)

Summary of Contents for Sumake ELSC-50H(V)

  • Page 1 INSTRUCTION MANUAL ELSC-50H(V), ELSC-60H(V) ITEM NO.: 2 IN 1 ELECTRIC CENTRAL-VACUUM SANDER/POLISHER W/5”(6”) HOOK (VINYL) PAD ELSC-50HM, ELSC-60HM ITEM NO.: 2 IN 1 ELECTRIC CENTRAL-VACUUM SANDER/POLISHER W/5”(6”) MULTIHOLE HOOK (VINYL) PAD ELSN-50H(V), ELSN-60H(V) ITEM NO.: 2 IN 1 ELECTRIC NON-VACUUM SANDER/POLISHER W/5”(6”) HOOK (VINYL) PAD ELSC(N)-B50(60)-I-1604A-X2...

  • Page 2: Important Information

    It should only be used for such sanding applications and within marked capacity and ratings. Only accessories specitfically recommended by SUMAKE should be used with this tool. Use in any other manner or with other accessories could lead to unsafe operating conditions.
  • Page 3 Correct or replace the suspect component. If abnormal noise or vibration still exists, return the tool to SUMAKE for repair or replacement. Refer to warranty instructions. Prior to use, inspect abrasive product and accessories for possible damage. If damaged, replace with new abrasive ...
  • Page 4 CAUTION To reduce the risk associated with environmental contamination: Do not throw electric power tools into the household waste! In accordance with the European Directive 2002/96/CE on  Waste Electrical and Electronic Equipment and transposition into national law, used electric power tools must be collected separately and recycled in an environmentally friendly manner.

  • Page 5: Operating Instructions

    Operating Instructions PRIOR TO THE OPERATION The tool is intended to be operated as a hand held tool. It is always recommended that while using the tool, operators stand on a solid floor, in a secure position with a firm grip and footing. Be aware that the sander can develop a torque reaction. STARTING AND STOPPING SANDER 1.
  • Page 6 Downforce Overload System The Sander has the ability to monitor and maintain the preset Maximum Speed as user downforce increases or decreases during use. During periods of overly high user downforce, the Sander will flash the LED on the back of the tool from Green to Red and cause the motor to slow slightly as a warning to the user.Continuous downforce should be no greater than approximately 5Kg (11 lb.).
  • Page 7 Federal Communications Commission (FCC) Compliance Statement IMPORTANT NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This manual is also suitable for:

Elsc-60h(v)Elsc-50hmElsc-60hmElsn-50h(v)Elsn-60h(v)

Table of Contents