Table of Contents
Advertisement
Quick Links
Fusion2 mod.2022
Table Saw
Operating Instructions
Producer:
Laguna Tools Inc
744 Refuge Way, Suite 200
Grand Prairie, Texas 75050
USA
Phone: +1 800-234-1976
Website: www.lagunatools.com
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
PDF ONLINE
E-mail: sales@igmtools.com
www.igmtools.info
Website: www.igmtools.com
2022-10-25
151-Fusion2 LAGUNA Table Saw Manual EN v1.02.02 A4ob
Advertisement
Table of Contents
Related Manuals for laguna Fusion2 2022
Summary of Contents for laguna Fusion2 2022
- Page 1 Phone: +1 800-234-1976 Website: www.lagunatools.com Distributor: IGM nástroje a stroje s.r.o. Ke Kopanině 560, 252 67, Tuchoměřice Czech Republic, EU Phone: +420 220 950 910 PDF ONLINE E-mail: sales@igmtools.com www.igmtools.info Website: www.igmtools.com 2022-10-25 151-Fusion2 LAGUNA Table Saw Manual EN v1.02.02 A4ob...
- Page 2 www.igmtools.com...
- Page 3 www.igmtools.com...
-
Page 4: Table Of Contents
Dear Woodworker, Thank you for your purchase and welcome to the Laguna Tools group of discerning woodworkers. We understand that you have a choice of where to purchase your machines and appreciate the confidence you have in the Laguna Tools brand. -
Page 5: Main Features
machine : not exceed 50% at 35°C. moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. • Intended use also involves compliance with our specified operating, maintenance and repair • If devices are provided for the connection of conditions and the safety information contained dust extraction and collection facilities, ensure in the operating instructions. -
Page 6: Guarding Related Warnings
• Disconnect the plug from the power source A guard that is loose, damaged, or is not misalignment, binding and kickback. and/or remove the battery pack, if detachable, functioning correctly must be repaired or • Never reach around or over a rotating saw from the power tool before making any replaced. -
Page 7: Electrical
CE norms, standards and regulations • Remove tools, wood scraps, etc. From The operating conditions for noise for safe use. Laguna Tools or IGM is in no the table before the table saw is turned measurement comply with Annex A of ISO way responsible for injury or death that occurs on. -
Page 8: Machine Overview
6. Setup machine before changing the fuse. Safety gloves should be worn. Use Caution: Your new Laguna Tools machine Arbor height control is heavy. Use a minimum of two people when lifting the tool into position and moving the tool 5. -
Page 9: Inventory
Receiving your tablesaw away the oil with a waste rag. Blade Guard Use Caution: An oily rag can be a serious fire hazard. Discard in an appropriate manner. Tech Tip: To help keep your table top clean and to prevent or clean any rust, we recommend waxing your tabletop with an appropriate wax rubbing compound. -
Page 10: Installing/Removing The Throat Plate
pieces. STOP BEFORE TIGHTENING. and nuts to the short rear fence guide and the back left of the table. STOP BEFORE TIGHTENING: Keep bolts loose until entire rail assembly is in place to properly level rail. 6.5 Installing/removing the throat plate 1. -
Page 11: Installing/Removing The Blade
Keep firm hold of the blade guard with left hand Set the arbor tilt to 0 degrees and lock the arbor Laguna, has not been tested with this product, and engage the cam lock with the thumb of to prevent it from moving when installing or use of such accessories with this tool could be your right hand. -
Page 12: Adjustments
(mitre slots) to effectively UNPLUGGED. With the blade in a high make the fence parallel to the blade. Your Laguna Tools machine comes fully position, bring the fence close to — but not adjusted from the factory, but it is good practice touching —... -
Page 13: Arbor And Tilt Adjustments
Better Loosen Table Bolts 3. Take relative measurement A dial indicator on a mitre gauge. Locate and loosen right side table to cabinet bolt (above the tool holder). Place the extension wing on the supports and Best place into position. Loosen Table Bolts 4. -
Page 14: Accessory Adjustments
3. Remove tool storage cover 4. Tighten or loosen with weight of motor. removing the table top. The belt can easily be changed without removing the table top. Use Caution: DO NOT OVERTIGHTEN BELT! The weight of the motor is adequate to put Accessing the Belt enough tension on the belt. -
Page 15: Push Block And Push Stick
Warning: Always turn on the dust collector As Adjustments are made, the blade before starting the saw and stop the saw before attachments will translate, not rotate, by design. turning off the dust collector. This ensures that the workpiece will not get held up. -
Page 16: Ripping Small Workpieces
OFF, slide it up close to the blade to align the outer edges of To keep you Laguna Tools machine in top the teeth with your cut mark (see pic). performance for many years please follow... - Page 17 10. Trouble-Shooting Machine will not start or continues to trip the breaker. Possible Causes Possible Solution 1. Start capacitor at fault. 1. Test/replace if faulty. 2. Motor connection wired wrong. 2. Correct motor wiring connections. 3. Wiring at fault. 3. Check/fix broken, disconnected, or corroded wires. 4.
- Page 18 Wiring Diagram: Fusion 2 230V www.igmtools.com -18-...
- Page 19 Fence assembly www.igmtools.com -19-...
- Page 20 Mitre gauge, blade guard www.igmtools.com -20-...
- Page 21 Motor and trunnion www.igmtools.com -21-...
- Page 22 Cabinet www.igmtools.com -22-...
- Page 23 List of components 102 381463-901 Fix Bushing 925200-000 Fence Assembly L\H (800mm) 103 000304-113 Pan Head Screw M6*1.0P*30 924708-000 Blade Guard Assembly US Type 104 174789-000 Motor Cover 924562-001 Miter Gauge Assembly 105 051135-000 Trunnion Support 051437-000 Extension Table 106 000003-104 Hex.