Declaration Of Conformity; Operation - Bosch System Controller Original Operating Instructions

Operating unit
Weight
Bluetooth® Low Energy 5.0
– Frequency
– Transmission power
The licence information for the product can be accessed at the following Internet address: www.bosch-ebike.com/licences

Declaration of Conformity

Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the System Controller/Mini Remote/Mini Remote
Dropbar radio communication unit complies with Directive
2014/53/EU. The full text of the EU Declaration of Conform-
ity can be accessed at the following Internet address:
www.bosch-ebike.com/conformity.
Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the System Controller/Mini Remote/Mini Remote
Dropbar radio communication unit complies with the Radio
Equipment Regulations 2017 (SI 2917/1206). The full text
of the UK Declaration of Conformity can be accessed at the
following Internet address:
www.bosch-ebike.com/conformity.

Operation

Requirements
The eBike can then only be switched on when the following
requirements are met:
– A sufficiently charged eBike battery is inserted (see oper-
ating instructions for the eBike battery from the system
generation the smart system).
– The speed sensor is connected properly (see operating
instructions for the drive unit from the system genera-
tion the smart system).
Operating unit power supply (System
Controller)
If a sufficiently charged eBike battery is inserted into the
eBike and the eBike is switched on, then the internal operat-
ing unit battery is powered and charged.
Please contact your bicycle dealer if the internal battery of
the operating unit is defective.
Operating Unit (Mini Remote/Mini Remote
Dropbar) Power Supply
The Mini Remote/Mini Remote Dropbar operating unit is
supplied with energy by a CR1620 coin cell.
Changing the coin cell (Mini Remote/Mini
Remote Dropbar)
If the coin cell of the operating unit Mini Remote/Mini Re-
mote Dropbar (1) is running low, the LED indicator light (3)
will flash orange.
Bosch eBike Systems
Mini Remote
g
MHz 2400–2480
mW
To change the coin cell, remove the operating unit Mini Re-
mote/Mini Remote Dropbar from the handlebars. Remove
the rubber insert (9). Remove the used coin cell and insert a
new one of type CR1620 into the battery holder. Close the
battery compartment by the rubber insert (9). Check that
the rubber insert (9) is correctly inserted to ensure the bat-
tery compartment is fully sealed. The LED indicator light (3)
will flash green to indicate that the coin cell has been inser-
ted correctly. Then secure the Mini Remote/Mini Remote
Dropbar operating unit onto the handlebars.
Note: Carefully tighten the fastening screw (7) (0.6 Nm).
Note: The connection to the System Controller is not inter-
rupted when the coin cell is changed.
You can obtain the coin cells recommended by Bosch from
your bicycle dealer.
Switching the eBike On and Off
To switch on the eBike, briefly press the on/off button (12).
After the starting animation, the state of charge of the eBike
battery is displayed in colour with the battery charge indic-
ator (13) and the set assistance level with the (10) display.
The eBike is ready to ride.
The display brightness is controlled by the ambient light
sensor (11). Therefore, do not cover the ambient light
sensor (11).
The drive is activated as soon as you start pedalling (except
at assistance level OFF). The drive power varies depending
on the assistance level set.
As soon as you stop pedalling when in normal operation, or
as soon as you have reached a speed of 25/45 km/h, the
drive switches off the assistance. The drive is automatically
reactivated as soon you start pedalling again and the speed
is below 25/45 km/h.
To switch off the eBike, press the on/off button (12) briefly
(< 3 s). The battery charge indicator of the eBike bat-
tery (13) and the assistance level LED (10) go out.
If no power is drawn from the drive for about 10 minutes
(e.g. because the eBike is not moving) and no button is
pressed, the eBike will switch off automatically.
Quick Menu
Selected settings are displayed on the quick menu. These
settings can also be changed while riding.
You can access the quick menu by pressing and holding
(> 1 s) the select button .
It cannot be accessed from the status screen.
The following settings can be changed via the quick menu:
– <Reset trip>
English – 3
Mini Remote Dropbar
16
2400–2480
≤ 1.9
0 275 007 3RC | (01.06.2023)
20
≤ 1.9