Pre-Operational Inspection; Pre-Operational Inspection Table - Snorkel MHP15HD Operator's Manual

At the start of each work day (or 8 hour shift), an
MHP15/44HD V2 qual i fied op er a tor must per form
the Pre-op er a tional In spec tion as listed in the ta ble
be low.
The pur pose of the Pre-op er a tional In spec tion is to
keep the MHP15/44HD V2 in proper work ing con di -
tion and to de tect signs of mal func tion at the ear li -
est pos si ble time.
This chap ter shows how to per form the in spec tion
and main te nance re quired for each item in the
Pre-op er a tional In spec tion Ta ble.

Pre-operational Inspection Table

Item
Stabiliser/Boom interlock test
Engine fuel level
Fuel tank cap
Engine oil level
Fuel leaks
Engine coolant
Wiring harnesses
Battery terminals
Battery fluid level
Hydraulic oil level
Hydraulic oil leaks
Tires and wheels
Bolts and fasteners
Structural damage and welds
Lanyard anchor points
Platform gravity gate
Platform guardrails
Flashing light (option)
Ground control switches
Ground control valve levers
Ground emergency lower valve
Emergency lower
Platform control box switches
Platform control valve levers
Platform emergency lower valve
RCD/ELCB AC outlet (option)
Platform work lights (option)
Placards and decals
Low Voltage Insulated MHP15/44HD V2 only*
Insulation covers
Fibreglass basket
Fibreglass basket emergency exit hatch
Boom insulation covering
Cleanliness
* For fur ther de tails on per form ing in su la tion tests please re fer to the Re pair Parts manual
MHP15/44HD V2 – 13620-1

9. Pre-operational Inspection

The MHP15/44HD V2 should be in the STOWED
POSITION and the Mas ter Key Switch set to OFF
be fore you be gin this in spec tion.
De fec tive parts and/or equip ment mal func tions
jeop ar dize the safety of the op er a tor and other per -
son nel, and can cause dam age to the ma chine.
DO NOT operate an MHP15/44HD V2 that is
known to be damaged or malfunctioning.
R e p a i r a l l
m a l f u n c t i o n s ,
MHP15/44HD V2 into service.
Service Required
Perform the test to ensure the system is functioning
Look to see that the fuel tank is full
Check to see that the cap is tight
Check oil level (between dipstick lines)
Visually inspect (hoses and connections)
Check that grills are not blocked
Visually inspect (installation, condition)
Visually inspect (no corrosion)
Check fluid level (1/4" or 6 mm below filler neck)
Visually inspect level (between lines on dipstick)
Visually inspect (hoses, tubes)
Visually inspect (condition)
Visually inspect (condition)
Visually inspect (weld cracks, dents)
Visually inspect (condition)
Check condition and operation
Visually inspect (condition)
Visually inspect (operation)
Actuate and inspect for proper operation
Check operation (causes correct motion)
Check operation (causes correct motion)
Check operation (causes correct motion)
Actuate and inspect for proper operation
Check operation (causes correct motion)
Check operation (causes correct motion)
Check operation
Check operation
Visually inspect (installation, condition)
Visually inspect (for cracks or damage)
Visually inspect (for cracks or damage)
Check operation
Visually inspect (for signs of cracking or corrosion)
Check all insulated surfaces (including basket) for road grime, dirt and
other contaminants
Rev B
DANGER
e q u i pm e n t d a m a g e
b e f o r e p l a c i n g
o r
t h e
page 9 - 1