Parameters Of The Expert Level With Diagnostics And Test - Siemens KNX RDG400KN Basic Documentation

Name
Expert level
P30 Heat P-band Xp/switching diff
P31 Cool P-band Xp/switching diff
P32 Radiator P-band Xp/swi diff
P33 Dead zone Comfort mode
P35 Integral action time Tn
RDG400KN
RDG405KN
P36 H/C ch'over swi point cooling
P37 H/C ch'over swi point heating
P38 Input X1
RDG400KN
(range 0..3 [ECO]..8)
RDG405KN
(range 0..3 [PROT]..10)
P39 Normal position input X1
P40 Input U1
P42 Input D1
RDG400KN
(range 0..3 [ECO]..7)
RDG405KN
(range 0..3 [PROT]..10)
P43 Normal position input D1
P44 Actuator running time Y1/Y2
P46 Output Y1/Y2
P47 Controller output VAV
P51 Flow temp limit floor heating
P54 Fan overrun time
P63 Supply air limit value min
P64 Supply air limit value max
P65 Protection heating setpoint
P66 Protection cooling setpoint
P68 Temporary Comfort mode
P69 Temporary Comfort setpoint
68 / 86
Siemens
Smart Infrastructure
3.13.4 Parameters of the Expert
level with diagnostics and
test
Factory setting
2 K
1 K
2 K
2 K
5 min
45 min
16 °C
28 °C
1: = Ext. sensor
0 (NO)
0
3 =
Operating mode
contact (RDG400KN)
Window contact
(RDG405KN
0 (N.O.)
150 s
On/Off (1)
0 = DC 0...10 V
Off
60 s
0%
100%
8 °C
Off
0 (= Off)
Off
RDG400KN,RDG405KN Basic documentation
Range
0.5...6 K
0.5...6 K
0.5...6 K
0.5...5 K
0...10 min
0...120 min
10...25 °C
27...40 °C
0 = --- (no function)
1 = Room temp ext. sensor/
return air temp (AI)
2 = H/C changeover (AI/DI)
3 = Operat. mode contact [ECO],
window contact [PROT] (DI)
4 = Dewpoint sensor (DI)
5 = Enable electric heater (DI)
6 = Fault input (DI)
7 = Monitoring input (Digital)
8 = Monitoring input (Temp)
10 = Presence detector (DI)
0 = Normally open/open
1 = Normally closed/close
0 = No function
1 = Input for air damper position
2 = input CO sensor
2
0 = --- (no function)
2 = H/C changeover (DI)
3 = Operat. mode contact [ECO],
window contact [PROT] (DI)
4 = Dewpoint sensor (DI)
5 = Enable electric heater (DI)
6 = Fault input (DI)
7 = Monitoring input (Digital)
10 = Presence detector (DI)
0 = Normally open/open
1 = Normally closed/close
20...300 s
0 = 3-position
1 = 2-position - ON/OFF
2 = 2-position - PWM
0 = DC 0...10 V
1 = 3-position
Off, 10...50 °C
0...360 s
0...P64 (%)
P63...100 (%)
OFF, 5...WCoolProt;
WCoolProt = 40 °C max.
OFF, WHeatProt... 40;
WHeatProt = 5°C min.
0...360 min
OFF = Disabled
ON = Enabled
ü ü
ü ü
ü ü
Appl
ü ü
Appl
ü ü
P46, P47
ü ü
P38
ü ü
P38
ü ü
ü ü
P38
X ü
ü ü
ü ü
P42
ü ü
P46
ü ü
Appl
ü ü
Appl
ü ü
P38
ü ü
ü ü
ü ü
ü ü
ü ü
ü ü
P02
ü ü
CE1P3192en
2019-04-12