Resetting Thermal Protection; Important - Hot Blending Instructions - Waring MX Series Manual

NOTE: 25% is the default speed setting in the reprogramming mode.
3. Press Speed Up or Speed Down
The increment is 1% (150 RPM). Press and hold the button to quickly
scroll through speeds. The speed can be set between 15% and 100%.
4. Once required speed is reached, press
to confirm setting. The LCD will now prompt "USE UP/DOWN TO SET
TIME". NOTE: Five seconds is the default time setting in the
reprogramming mode.
5. Use Speed Up or Speed Down
90 seconds). Once 90 seconds are reached, pressing Speed Up
not increase the value and the LCD will prompt "MEMORY LIMIT" for
2 seconds.
6. Press button or wait 5 seconds to confirm the setting. When the
blending time is confirmed, the LCD will prompt SELECT ANOTHER
SPEED. Repeat steps 3–5 if additional processing is needed.
NOTE: When pressing Speed Up
speed for next section, the LCD will prompt "USE UP & DOWN TO SET
SPEED: 25%".
7. To save the new program settings, press both Speed Up
Down buttons simultaneously. The LCD will prompt NEW PROGRAM
(PROG #) SAVED for 5 seconds. The blender will return to STANDBY
mode and the LCD will prompt "PRESS ANY BUTTON TO BLEND".
NOTE: If no button is pressed for 60 seconds when prompted to "ADD
NEW PROGRAM", the blender will exit NEW PROGRAM mode and will
return to STANDBY mode. The new program will not be stored.
8. To run new programs, simply press the desired Program button and the
blender will run the program set by the user. The LCD will display NEW
PROGRAM # and will count down the set time.
RESTORING FACTORY-SET BEVERAGE STATIONS
1. To restore factory-set default beverage stations, press both
Speed Up and Speed Down
PROGRAM.
2. Press button. LCD will prompt RESTORE DEFAULT PROGRAMS.
3. Press button to confirm and save. The LCD will display the logo for
3 seconds.
4. The unit will return to STANDBY mode and the LCD will prompt PRESS
ANY BUTTON TO BLEND.
NOTE: The STOP
key will abort this process at any point before
restoring default programs is confirmed.
button to set the speed value.
button or wait 5 seconds
button to set the time value (up to
or Speed Down buttons to set
and Speed
buttons. LCD will prompt ADD NEW
8
Your reprogrammable blenders are equipped with a drink counter to keep
track of daily drink totals and total drink counts for your machine. To display
the counts, hold program buttons
Your display will read:
DAILY COUNT XXXX
TTL COUNT XXXXX
Daily Count will display the numbers of drinks mixed per day. Total Count
is the accumulation of all drinks made since first use of the blender.
The Daily Count can be reset by holding in Program buttons
will
simultaneously for 3 seconds then, pressing ON/OFF button for 3 seconds.
Daily Count will reset to zero and Total Count will remain unchanged.
If Total Count needs to be reset, call your nearest Waring authorized service
facility for information.
NOTE: Use of the PULSE features will not add to the daily or total drink
counts.
• The blender you have purchased is equipped with an Automatic Reset
Switch to protect the motor from overheating.
• If your blender stops running under heavy use, turn the power switch to the
STANDBY or OFF position and unplug the power cord. Empty the blender
container of all its contents and allow approximately 5 minutes for the
motor to cool down.
• Plug the power cord back into the outlet and continue blending.

IMPORTANT - HOT BLENDING INSTRUCTIONS

To minimize the possibility of being scalded when blending hot materials,
the following precautions and procedure must be observed.
• Hot materials are those that are 100°F (38°C) or hotter.
• Limit the amount of materials processed to 1 pint.
• Completely remove the center portion of the two-piece container lid before
starting motor (this will allow venting of the rapidly heated and expanded
air inside the container when blender is running).
• Always start blending on lowest speed setting, and then progress to
desired speed.
• Never stand directly over blender when it is being started or while it
is running.
DRINK COUNTER
& simultaneously for 3 seconds.

RESETTING THERMAL PROTECTION

9
&