Waring MX Series Manual page 6

INSTALLING THE SOUND ENCLOSURE
NOTE: If you are installing a sound enclosure as an optional accessory,
remove the standard jar pad to access the screw holes on the upper
housing. This jar pad will not fit properly with the sound enclosure. To remove
it, peel it back, starting in the corner and working your way over the drive
coupling until it is completely off the base unit, as seen in Figures 1, 2 and 3.
Figure 1 Figure 2
Figure 6 Figure 7
Figure 11 Figure 12
Once you have finished removing the standard jar pad OR if your blender
came packed with a sound enclosure, follow these instructions:
Step 1: Find the 3 screw holes located on the left, back and right sides of
the upper housing as seen in Figures 4, 5 and 6.
Step 2: Place the base of the sound enclosure on the motor housing so the
screw holes on the enclosure line up with the screw holes on the
base. Use a Phillips-head screwdriver and the 3 screws included
with sound enclosure to secure the enclosure to the base unit in the
3 locations as seen in Figures 7, 8 and 9.
Step 3: Once the sound enclosure is secured tightly, select the custom jar
pad (included with sound enclosure). Please note the standard jar
pad will NOT fit properly with the sound enclosure. The correct
custom jar pad has a recessed area around the outer edge. It also
has a curved front with tabs on the sides, as seen in Figures 10, 11,
and 12. This curved area should face the front of the blender.
Step 4: Attach custom jar pad included with sound enclosure onto upper
housing with the curve facing out, as seen in Figure 13. Press tightly
around coupling to secure custom jar pad onto upper housing, as
seen in Figures 14 and 15.
Figure 3 Figure 4
Figure 8 Figure 9
Figure 13 Figure 14
10
To remove the sound enclosure, unplug your blender and follow these steps:
1. Open sound enclosure and remove blender container.
2. Remove front portion of sound enclosure by disengaging both sides at
the pivot point.
2. Remove rubber jar pad.
4. Remove 3 screws from blender base and remove sound enclosure.
Whether your blender is in STANDBY mode, NEW PROGRAM mode, or
the motor is running, pressing the ON/OFF
from running and will turn the power off. The LCD display will turn off.
NOTE: All programs and current settings will be restored next time you
Figure 5
turn unit on.
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE
OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL
TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY,
Figure 10
RENDERING THEM INEFFECTIVE.
• Wash, rinse, sanitize and dry container prior to initial use and whenever
it will not be used again within a period of 1 hour.
• Wash and rinse container after each use.
• Clean and sanitize motor base prior to initial use and after each use.
• Washing solutions based on non-sudsing detergents and chlorine-based
sanitizing solutions having a minimum chlorine concentration of 100 PPM
Figure 15
are recommended.
The following washing, rinsing, and sanitizing solutions, or their equivalents,
may be used.
SOLUTION
Washing
Rinsing
Sanitizing
• In repetitive batch-processing applications, frequent cleaning of the
container will prolong the life of the blade assembly. In no case should
actual running time between cleanings exceed ½ hour.
• Do not use container to store processed foods or beverages.
REMOVING THE SOUND ENCLOSURE
TURNING OFF YOUR BLENDER
CLEANING AND SANITIZING INSTRUCTIONS
PRODUCT DILUTION IN WATER TEMPERATURE
Diversy Wyandotte 4 Tablespoons/
Diversol BX/a or CX/A 3.8 Litres
Plain Water
Clorox 1 Tablespoon/
®
Institutional Bleach 3.8 Litres
11
button will stop the unit
Hot 46˚C
Warm 35˚C
Cold 10 – 21˚C