Important Safeguards - Waring MX Series Manual

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be
taken, including the following:
READ ALL INSTRUCTIONS.
1.
2. Always unplug from outlet when not in use, prior to handling, before
putting on or taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse the blender base
in water or other liquids.
4. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge. Children should be supervised to ensure they
do not play with the appliance.
5. Avoid contact with moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions or is dropped or damaged in any manner.
Return appliance to the nearest authorized service facility for
examination, repair, or electrical or mechanical adjustment.
7. The use of attachments, including canning jars, not recommended by the
appliance manufacturer may cause hazards.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter or touch hot surfaces.
10. Keep hands and utensils out of container while blending, to prevent the
possibility of severe personal injury and/or damage to the blender.
A rubber scraper may be used, but must be used only when the blender
is not running.
11. Blades are sharp. Handle carefully.
12. Always operate blender with cover in place.
13. When blending hot liquids, remove center-piece of two-piece cover.
See Hot Blending Instructions.
14. The use of ear protection is recommended during extended
operating periods.
15. See Cleaning and Sanitizing Instructions for all Waring Blenders. NOT
FOR WATERJET CLEANING.
16. The appliance must be positioned so that the plug is accessible.
17. DO NOT use carbonated liquids in the blender jar or any blending
container. Using carbonated liquids in the blender jar or any blending
container may result in injury.
18. DO NOT blend oil or oil-based products such as peanut butter for
greater than 5 minutes.
19. Never remove blender jar from base unit until the blade and coupling
have completely stopped.
SAVE THESE INSTRUCTIONS
2
MX MECHANICAL SWITCHES
1. Before starting, make sure that the blender is
unplugged and container is not positioned on
the blender.
2. Put ingredients into container and cover it. Do not
fill above MAX line.
3. With the unit in STANDBY
container on blender base. Be sure container is
fully seated and that drive coupling is properly
engaged. Plug blender cord into outlet.
4. This blender has 2 speed settings: HI
to desired position. To crush ice quickly, use HI
5. When finished blending, set paddle switch to STANDBY
6. This blender is equipped with a PULSE
down to engage PULSE
paddle switch is released.
7. Allow motor to come to a complete stop before removing container from
blender base. Never place the container on the motor base or remove it
from the motor base while motor is running.
8. Always hold container with one hand when starting and while blending.
Never operate without jar lid.
9. Wash and dry container after each use. See Cleaning and Sanitizing
instructions.
MX ELECTRONIC TOUCHPAD SWITCHES
WITHOUT SOUND ENCLOSURE
1. Before starting, make sure that the blender is
unplugged and container is not positioned on
the blender.
2. Put ingredients into container and cover it. Do not
fill above MAX line.
3. Place container on blender base. Be sure container
is fully seated and that drive coupling is properly
engaged. Plug blender cord into outlet.
4. This blender is equipped with an electronic membrane keypad. The key-
pad has a main power STANDBY
PULSE buttons.
5. Press the STANDBY button to turn on the blender. Green LED will
illuminate. For continuous operation, press either LO or HI
When finished blending, press STOP
press the PULSE button; motor will run on HI
button is released.
NOTE: Your MX Electronic Blender uses a Slow Start
pressing HI , the unit will start in the LO speed for 2 seconds and
then switch to HI speed. This allows for a more even blending of ingre-
dients in container.
position, place
and LO . Press Paddle Switch
speed setting.
option. Hold paddle switch
function. Unit will run on HI speed until the
button, plus HI , LO , STOP
. For momentary operation,
speed until the
feature. When
™
3
position.
and
button.