Waring MX Series Manual page 4

4. The motor speed can be adjusted by pressing the
buttons. Speed ranges from 15% to 100%.
100% 20,000 RPM
50% 10,000 RPM
15% 3,000 RPM
The Speed Up button will increase the motor speed display in 1%
increments and the Speed Down
speed display in 1% increments. Holding down either button will quickly
scroll through speeds.
Using the Speed Up and Speed Down
speed. If no speed is selected, motor will default to 100%.
NOTE: The motor does not run at the newly set speed until the START/
STOP button is pressed. If START/STOP
within 5 seconds, the new speed setting will be stored for next use and
the blender will return to STANDBY mode; the display will once again
read "PRESS ANY BUTTON TO BLEND".
5. Press START/STOP button to run the blender. Blender will run
continuously at the set speed. The LCD will display the motor speed in
percentage. Default speed (percentage) is at 100%. Motor speed can be
changed while blender is running by simply pressing Speed Up
Speed Down button.
6. To stop continuous blending operation, press START/STOP
press any of the program buttons.
PULSE FEATURES
Your unit comes equipped with two PULSE options: Normal Pulse
Maximum Pulse . Note: The Pulse buttons are momentary switches –
once released, the unit will shut off.
1. To use Max Pulse option, press the
at 150% speed. The LCD will read "MAX PULSE SPEED: 150%".
2. To use Normal Pulse option, press the
at 100% speed. The LCD will read "NORM PULSE SPEED: 100%".
3. The blender allows you to set the pulse to your desired speed. While
blending at Normal Pulse speed, the motor can be adjusted. To do this,
hold the Normal Pulse button and press Speed Up
Down button to adjust the blending speed. The LCD will show the
setting speed and motor speed will change.
NOTE: The speed can be set from 15% to 100%. Once the
button is released, the motor will shut off and the blender will return to
standby mode. The changed pulse speed will be stored in memory to
replace the default speed at 100%.
or Speed
button will decrease the motor
buttons, set desired motor
button is not pressed
button or
button. This will run the motor
button. This will run the motor
or Speed
Pulse
6
1. There are 4 Program buttons for four reprogrammable beverage stations
for easy operation and consistent results. The factory-set stations are
programmed as listed below:
2. To run any of the above preset programs, blender must be in
STANDBY mode.
3. Press desired Program button to start the blender. The motor will run at
the preset speed within the preset blending time. The LCD will show time
remaining. Once the blender counts down to 0, the motor will stop
running and the blender will return to STANDBY mode and prompt
"PRESS ANY BUTTON TO BLEND".
NOTE: To terminate a blending program, simply press START/STOP
button or any of the Program buttons. After doing this, the blender will
return to STANDBY mode and LCD will prompt "PRESS ANY BUTTON
TO BLEND".
or
Users can add 4 new programs to meet their needs. A program can
consist of several sections, each with a different speed and running time.
For example,
as shown below:
and
Section 1: speed = 75%; time = 30 seconds
Section 2: speed = 100%; time = 20 seconds
Section 3: speed = 50%; time = 20 seconds
The program has the following limitations:
Speed: 15% to 100%
Time: 5 to 90 seconds
Total running time in a program cannot exceed 90 seconds, i.e., sum
of the sections cannot be longer than 90 seconds.
NOTE: The button will act as the enter key to proceed to next step
during the reprogramming process.
1. To enter new program, press both Speed Up
buttons simultaneously while unit is in STANDBY mode. The blender will
enter new programming mode and the LCD will prompt "ADD NEW
PROGRAM".
2. Next, you will need to set values. Press the Program button you want
to replace (i.e., 1... 4). The LCD will prompt "USE UP/DOWN TO SET
SPEED: 25%".
REPROGRAMMABLE STATIONS
Liquid drinks
Frozen drinks
Ice cream drinks
Smoothies
REPROGRAMMING BEVERAGE STATIONS
can be replaced with a new program that has 3 sections,
7
and Speed Down