Table of Contents
Advertisement
When using the cleaning function, you can clean
Note:
the enamel accessory provided at the same time. You
cannot clean any of the wire racks when using the
cleaning function. The wire racks are not suitable for
cleaning using the cleaning function; this will discolour
them. Further accessories suitable for cleaning using
the cleaning function are listed in the table for special
accessories. ~ "Accessories" on page 12
:
Warning
Risk of fire!
Loose food residues, grease and meat juices may
■
catch fire during the cleaning function. Before
starting the cleaning function, remove coarse dirt
from the cooking compartment and from the
accessories.
The appliance will become very hot on the outside
Risk of fire!
■
during the cleaning function. Never hang
combustible objects, e.g. tea towels, on the door
handle. Do not place anything against the front of
the appliance. Keep children away from the
appliance.
:
Warning – Risk of serious damage to health!
The appliance will become very hot during the cleaning
function. The non-stick coating on baking trays and tins
is destroyed and noxious gases are released. Never
clean non-stick baking trays and baking tins using the
cleaning function. Only clean enamelled accessories
using the cleaning function.
Setting the cleaning function
Before setting the cleaning function, ensure that you
have followed all instructions for preparation.
The duration of each cleaning setting is preset and
cannot be changed.
Touch the menu field.
1.
The list of operating modes is displayed.
Touch the "Cleaning" text field.
2.
Touch the "Pyrolytic self-cleaning" text field.
3.
The cleaning setting is highlighted in white on the
display.
Turn the rotary selector to set the cleaning setting.
4.
The end time is calculated automatically at the same
time.
Press the l Start/Stop button to start.
5.
The cooking time counts down on the display. The
heating line does not appear for the cleaning
function.
The cleaning function starts.
Ventilate the kitchen when the cleaning function is
running.
The appliance door locks shortly after the function starts
running.A message and the n symbol appear on the
display.
When the cleaning function has ended, an audible
signal sounds. The cooking time 00 m 00 s is shown on
the display. Press the ÿ On/Off button to switch off the
appliance.
The appliance door cannot be reopened until the
n symbol for the locking mechanism goes out.
Setting a later end time
You can set a later end time. Before starting the
appliance, touch the "End" text field and set a later end
time using the rotary selector.
The appliance switches to standby after it is started. The
end time can no longer be changed.
Changing and cancelling
After starting the appliance, the cleaning setting can no
longer be changed.
If you would like to cancel the cleaning function, switch
the appliance off using the ÿ On/Off button. You can
no longer pause the operation using the l Start/Stop
button.
The appliance door remains locked until the n symbol
for the locking mechanism on the display goes out.
Once the cleaning function has ended
Once the cooking compartment has cooled down, use
a damp cloth to wipe off the ash that has been left
behind in the cooking compartment, in the accessories
on the racks and around the appliance door.
Wipe the pull-out rails with a damp cloth. Then slide the
pull-out rails in and out several times. After cleaning,
some discolouration may remain on the pull-out rails.
This has no effect on performance.
Very bad soiling may cause white deposits to
Note:
remain on the enamel surfaces. This is residue from the
food and is harmless. It does not affect performance.
You can remove these residues using lemon juice if
required.
Descaling
The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling programme.
For hygiene reasons, the descaling programme must
be run through completely so that the appliance can be
ready for operation again.In total, the descaling
programme runs for approx. 70-90 minutes.
Descale (approx. 55-70 minutes), then empty and
■
refill the water tank
First rinsing cycle (approx. 6-9 minutes), then empty
■
and refill the water tank
Second rinsing cycle (approx. 6-9 minutes), then
■
empty and dry the water tank
If the descaling process is interrupted (for example, due
to a power failure or because the appliance has been
switched off), you are prompted to rinse the appliance
twice after it is switched back on. The appliance cannot
be used until the second rinsing cycle has come to an
end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Cleaning function
en
29
Advertisement
Table of Contents
