Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland. DisplayPort is trademarks of Video Electronics Standards Association.
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals. WARNING CAUTION European U.K. Continental EU (except U.K.) U.K. Declaration of the Manufacturer Declaration of the Manufacturer and marked with English-2 Chinese Japanese China Japan NEC Display Solutions, Ltd. 4-13-23, Shibaura, Minato-Ku Tokyo 108-0023, Japan...
• Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. • The screen of the coaxial cable is intended to be connected to earth in the building installation.
Contents Your new MultiSync monitor box* should contain the following: • LCD monitor • Power cord* • Video Signal Cable • Wireless Remote Control and AA Batteries • Setup Manual Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) Power Cord* CD-ROM Remember to save your original box and packing material to transport or ship the monitor.
Please note the following when mounting on wall or ceiling • When using mounting accessories other than those that are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method. • NEC strongly recommends Unit using size M6 screws...
The protective sheet was wrapped around the LCD in the original packaging. Make sure there is nothing on the table that can damage the monitor. When using mounting accessories other than NEC compliant and approved, they must comply with the VESA-compatible mounting method.
Parts Name and Functions Control Panel POWER button Switches the power on/off. See also page 16. MUTE button Switches the audio mute ON/OFF. INPUT button Acts as SET button within OSD menu. (Toggle switches between [DVI], [DPORT], [VGA], [RGB/HV], [HDMI], [DVD/HD], [SCART], [VIDEO1], [VIDEO2] or [S-VIDEO]).
Terminal Panel AC IN connector Connects with the supplied power cord. Main Power Switch On/Off switch to turn main power ON/OFF. LAN port (RJ-45) LAN connection. See page 31. REMOTE IN/OUT Use the optional wired remote control by connecting it to your monitor.
Internal/External speaker switch Switch to turn internal speaker/external speaker. : Internal speaker : External speaker. NOTE: Please power off the monitor when you use the Internal/External speaker switch. Kensington Lock For security and theft prevention. Option board slot Slot 1 and slot 2 type accessories are available. Please contact your supplier for detailed information.
PIP (Picture In Picture) button ON/OFF button: Toggle switches between PIP, POP, PICTURE BY PICTURE-ASPECT and PICTURE BY PICTURE-FULL. See page 22. INPUT button: Selects the “picture in picture” input signal. CHANGE button: Replaces to the main picture and sub picture.
C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.
5. Attach the cable cover • Use two of the M4 screws (included) to attach the cable cover. P402/P462 P552 6. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer ﬁ...
Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Before making connections: First turn off the power of all the attached equipment and make connections.
Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards with a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. <Typical factory preset signal timing>...
Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD.
Power Indicator Mode Status Indicator Light Power ON Green* Power OFF Power consumption under 0.5 W* Power Save Amber Power consumption under 1 W* Power Standby when “SCHEDULE Green and Amber blink alternately SETTINGS” enabled Diagnosis (Detecting failure) Red Blinking (See Troubleshooting page 36) *1 If “OFF”...
Information OSD The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc. Press the DISPLAY button on the remote to bring up the Information OSD. Picture Mode DVI, VGA, RGB/HV, DPORT STANDARD sRGB AMBIENT1 HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO STANDARD CINEMA AMBIENT1...
OSD (On-Screen-Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item Sub Menu PICTURE MODE Select Press UP or DOWN button to select sub-menu. Remote Control Press UP or DOWN button to select.
(S-Curve). DICOM SIM. DICOM GSDF curve simulated for LCD type. PROGRAMMABLE A programmable gamma curve can be loaded using NEC optional software. MOVIE SETTINGS NOISE REDUCTION Adjusts the amount of noise reduction. Press + or - to adjust. VIDEO1, VIDEO2, S-VIDEO inputs only TELECINE Automatically senses the sources frame rate for optimal picture quality.
H RESOLUTION Adjusts the horizontal size of the image. VGA, RGB/HV inputs only V RESOLUTION Adjusts the vertical size of the image. VGA, RGB/HV inputs only INPUT RESOLUTION If there is a problem with signal detection, this function forces the monitor to display the signal at VGA, RGB/HV inputs only the desired resolution.
TIME Conﬁ gures the time for the real-time clock. DAYLIGHT SAVING Conﬁ gures daylight savings on or off. RESET Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER, SCHEDULE SETTINGS. KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off. When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.
INFORMATION OSD Selects whether the information OSD is displayed or not. The information OSD will be displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range. An interval between 3 to 10 seconds for the Information OSD to appear is available.
LAN SETTING When you use this function, EXTERNAL CONTROL should be “LAN”. NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN SETTING is applied. DHCP Enabling this option automatically assigns an IP address to the monitor from your DHCP server. Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator.
ADVANCED OPTION INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices are connected. NONE The Monitor will not search the other video input ports. FIRST DETECT When the current video input signal is not present, then the monitor searches for a video signal from the other video input port.
OVER SCAN Some video formats may require different scanning modes in order to best display the image. HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the image will be shown on the screen.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Remote Control Function REMOTE CONTROL ID FUNCTION REMOTE CONTROL ID The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors.
3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor. The Information OSD will be shown at top left side of the screen. Monitor ID: Displays the ID number of the current monitor within the daisy chain. Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor.
Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 23). Functions that can be controlled by a personal computer are: •...
Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NOTE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 23). To use a LAN connection, you are required to assign an IP address.
Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL.
Alert Mail Setting http://<the Monitor’s IP address>/lanconﬁ g.html This option notiﬁ es your computer of an error message via e-mail when using wired LAN. An error message notiﬁ cation will be sent when an error occurs in the monitor. Alert Mail Checking [ENABLE] will turn on the Alert Mail feature.
Alert error message list Error number Alert mail Message * ErrorCode The monitor’s power supply is not 70h ~ 7Fh functioning normally. 80h ~ Fh The cooling fan has stopped. The monitor’s back light unit is not 90h ~ 9Fh functioning normally.
FullScan Capability: Allows you to use the entire screen area in most resolutions, signiﬁ cantly expanding image size. VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Pin Assignment 1) RS-232C input/output Pin No Name connected to 7&8 connected to 6 connected to 4 connected to 1&8 connected to 1&7 This LCD monitor uses RXD, TXD and GND lines for RS-232C control. 2) REMOTE IN 3) REMOTE OUT D-SUB 9P English-40...
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly products, and always strive to help deﬁ...