Table of Contents
Advertisement
Quick Links
(6) Crescent
Rings 21045-8
(2) Retaining
Pins 302563
(2)
Toggle
Links
302562
(2) Spacers
314936-1 Ring
302016
†
Rivet
1-305678-5
Pivot Pin
300115
†
Insulation
(Between Links)
Indenter
314932-1
(4) External
Snap Rings
1-21048-6
(2) Retaining
Pins 300042
†
These items must be replaced by TE Connectivity to ensure reliability of the tool. See Section 6.
1. INTRODUCTION
This instruction sheet covers the use and maintenance
of STRATO-THERM Die Head Assembly 314915-1.
The head assembly is used in Pneumatic Crimping
Tool 69015 to crimp size 12-10 AWG
STRATO-THERM Terminals and Splices with
insulation barrel feature.
All dimensions on this sheet are in millimeters
NOTE
[followed by inches in brackets].
i
© 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
STRATO-THERM* Die Head Assembly
314915-1 for Use in Pneumatic
Crimping Tool 69015
Link 300114
Indenter
314930-1
Stop Bracket 314934-1
(2) Button Head Screws
2-21002-0, 8-32 X 6.4 [.25] Long
Link 3-59649-1
†
Insulation
Anvil 314931-1
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
STRATO-THERM
Die Head Assembly
†
Stop
314933-1
†
Nest
314929-1
†
Toggle
Lever 314935-1
Retaining Pin
8-59558-3
Adjustment Pin
302015
Front of
Die Assembly
Figure 1
Read these instructions completely and understand
them before using the head assembly.
Reasons for reissue of this document are provided in
Section 7, REVISION SUMMARY.
2. DESCRIPTION (Figure 1)
The head assembly components include a nest and
indenter for crimping the product wire barrel, and an
insulation anvil and insulation indenter for crimping the
product insulation barrel. There is an adjustment pin
for the insulation crimp that can be placed in any of
three positions. Position 1 is for the smallest insulation
sizes and position 3 is for the largest.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
Instruction Sheet
408-9736
19 DEC 11 Rev B
314935-1
Pneumatic Crimping
Tool 69015
1 of 4
LOC B
Advertisement
Table of Contents
Related Manuals for TE Connectivity STRATO-THERM 314935-1
Summary of Contents for TE Connectivity STRATO-THERM 314935-1
- Page 1 PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, *Trademark visit our website at www.te.com LOC B TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
- Page 2 408-9736 4. CRIMPING TERMINALS AND SPLICES 12-10 AVOID PERSONAL INJURY! Keep fingers clear of DANGER Wire crimp area. Be careful to keep body parts and other 8.74 [.344] objects away from trigger until ready to cycle tool. 9.53 [.375] STOP Wire Strip Length (Typ)
- Page 3 408-9736 Insert Wire Fully Wire Barrel Against Locator Splice Crimping (Ref) Terminal Ring or Remainder of Splice on Stop Bracket Figure 4 5.1. Daily Maintenance Wire Barrel At the close of each shift, the responsible operator Crimp Centered should clean foreign particles from the tool using a (Typ) soft, clean, lint-free cloth or brush.
- Page 4 408-9736 Suggested Plug Gage Design (Wire Barrel Crimp Area) 2.31 [.091] 2.46 [.097] “GO” Dimension “NO-GO” Dimension 2.36 [.093] Radius (Typ) 25.4 [1.00] 6.35 [.25] Minimum (Typ) Minimum (Typ) Die Closure Die Opening (Ref) Figure 6 Worn, cracked, pitted, or chipped die surfaces, or 4.
Need help?
Do you have a question about the STRATO-THERM 314935-1 and is the answer not in the manual?
Questions and answers