Cleaning And Maintenance; Delivery Set - Maxwell MW-2108 B Instructions Manual

ENGLISH
Step 4 – cutting the top of the head
Using the 9 mm attachment comb (8) or 12 mm
attachment comb (9) cut the hair on the top of
the head towards the crown against the hair
growth direction.
• You can cut hair against and along the hair
growth direction, but keep in mind that haircut
against the growth direction will be shorter than
the haircut along it.
• Use the 3 mm attachment comb (6) and 6
mm attachment comb (7) for very short hair-
cut. To leave longer hair, use the necessary 9
mm comb (8) or 12 mm attachment comb (9).
• To leave longer hair, take hair locks between
your fingers and cut hair using the clipper
(pic. 5).
• You can use the comb (11): lift the hair locks
and cut them above the comb (pic. 6).
• Always start cutting from the head back.
• Set the hair with the comb (11) to reveal
uneven locks.
• Use the scissors (12) to make haircut even
Step 5 - the final part
– In the final stage of haircut remove the attach-
ment comb from the unit, turn the the blades
of clipper towards the hair and carefully trim
hair on the temples and neck. Do not press
the clipper strongly, there is danger of injuries
or cuts when open blades come in contact
with skin (fig. 7).
– After finishing of hair cutting put the protec-
tive cover (10) on the blades (3, 4).
Cone-shaped haircut
Set the necessary attachment comb and start
cutting from the head back towards the crown.
Cut hair against hair growth from the head front
to the crown and on the head sides (Pic. 8). To
get a flat top haircut, use the comb (11): lift the
locks and cut them along the comb. Set the hair
with the comb (11) to reveal uneven locks.
Note: Between operations, you can hang the
clipper on the hanging loop (5) having pre-
liminarily switched the unit off using the power
switch (1).

CLEANING AND MAINTENANCE

Lubricating the blades
Regularly lubricate the blades with the oil (13)
supplied with the unit.
– Switch the unit off using the power switch (1)
and unplug it.
– Apply one-two drops of oil (13) on the teeth
of the blades (3, 4) and the back side of the
upper blade (4), turn the unit on and make
sure that the blades are moving smoothly.
– Switch the unit off. Clean the excess oil with
a dry cloth.
Attention! Use only the oil supplied with the
unit.
DO NOT use vegetable oil, fat, mixture of oil and
solvents for lubrication.
Solvents will evaporate, leaving the thick oil that
may slow down the blades motion.
Cleaning of hair clipper
– Switch off and unplug the unit.
– Clean the blades from the cut hair, using the
cleaning brush (14).
– Wipe the accessories and unit body with a
slightly wet cloth, and then dry them with a
soft cloth.
– Put the protective cover (10) on the blades
(3, 4).
– Do not immerse the clipper into water or
other liquids.
– Do not use solvents or abrasives for clean-
ing the unit.
Storage
– Before taking the unit away for storage clean
and lubricate the blades (3, 4) with lubricat-
ing oil (13) and put the protective cover (10)
on.
– Keep the unit in a dry cool place, out of reach
of children.

DELIVERY SET

1. Hair clipper (with blades) – 1 pc.
2. Attachment combs – 4 pcs.
3. Protective cover - 1 pc.
4. Comb – 1 pc.
5. Scissors – 1 pc.
6. Lubricating oil – 1pc.
7. Cleaning brush – 1 pc.
Technical specifications
Power supply: 230 V ~ 50 Hz
Maximal power consumption: 9 W
10