Advertisement
Available languages
Available languages
and the remaining thick oil can slow down the
upper blade (4) moving.
– For lubricating the blades use only the oil
(13), supplied with the unit.
Taper lever (2)
– Taper lever (2) for lower blade (3) moving is
located under the thumb (if you are right-
handed). When cutting hair you can move
the blade, pressing the lever (2), adjusting
the haircut length without usage of the comb
attachments. In the upper lever position, hair-
cut will be the shortest one. In the down lever
position the cutting length is approximately
the same as after 3 mm attachment comb (6)
usage. Changing the lever position while hair
cutting, you can select the necessary hair
cutting length.
– If hair is jammed in the blades (3, 4) while cut-
ting, move the lever (2) from the upper posi-
tion to the down position several times, this
will help to release the jammed hair without
removing the blades.
– When the unit is switched on, move the lever
several times from the upper position to the
lower position, this way you can remove the
cut-off hair from the blades.
– If the unit pulls hair while cutting, it means
that the blades (3, 4) became blunt, replace
them with new ones.
INSTRUCTIONS ON HAIR CUTTING
• The hair should be clean and dry when cut-
ting.
• Insert the power plug into the socket.
• Before cutting hair switch the unit on, moving
the power switch (1) to the position «ON» and
make sure that unit operates normally and
blades move smoothly. If there is excess oil
on blades, remove it with a dry cloth.
• Constantly check the power cord, prevent it
from multiple twisting, regularly switch the
unit off and straighten the power cord.
• Seat the person so that his/her head is
approximately at your eye level, cover the
person's shoulders with a towel and set hair
with the comb (11).
Reminder
– Always cut off a little amount of hair at a time
- if necessary you can always return to the
trimmed area again for additional cutting.
– The best haircut results are reached on dry
hair, not wet.
– Set hair with the comb (11) to reveal uneven
locks.
– It is better to leave longer hair after hair-cut-
ting for the first time.
– After learning your clipper better, you will
be able to arrange your hair in any style you
need.
Attachment combs
The length of hair depends on the attachment
used:
• Attachment comb (6): length of hair left 3
mm
• Attachment comb (7): length of hair left 6
mm
• Attachment comb (8): length of hair left 9
mm
• Attachment comb (9): length of hair left 12
mm
Set the attachment upper part on the blade and
press it until click. To remove the attachment
comb press the clamp and remove the attach-
ment.
Step one
Set the 3 mm attachment comb (6) or 6 mm
attachment comb (7). Switch the unit on using
the power switch (1), setting it to position «ON».
Hold the unit so that the blades are pointed up-
wards. Start the haircut from the beginning of
the hair growth. Slowly move the clipper upward.
This way cut the head back area at neck bottom
and near the ears (pic. 1, 2, 3)
Step two
Switch the unit off using the power switch (1) by
setting it to the "OFF" position, unplug the unit,
set the 9 mm attachment comb (8) for longer
hair or 12 mm attachment comb (9) and con-
tinue cutting hair near top of the head (pic. 4)
Step 3 – cutting temples
Switch the unit off, unplug it, set the 3 mm at-
tachment comb (6) or 6 mm attachment comb
(7) and cut hair in the area of temples. Then set
the 9 mm attachment comb (8) or 12 mm attach-
ment comb (9) and continue cutting towards the
top of the head.
9
ENGLISH
Advertisement
