Cleaning And Care; Delivery Set; Technical Specifications - Maxwell MW-2110 SR Manual Instruction

ENGLISH
the «9-12 mm» attachment (8) and continue cutting
towards the top of the head.
Step 4 – cutting the crown of the head
Using the «9-12 mm» attachment (8) cut the hair
from the top of the head towards the crown against
the hair growth direction.
Step 5 – the final part
Remove the attachment (7 or 8) from the unit, turn
the blades of the unit towards the hair and carefully
trim hair on the temples and neck. Do not press hard
on the unit; there is danger of injuries or cuts when
open blades come in contact with the skin.
Cone-shaped haircut
Set the necessary attachment (7 or 8) and start cutting
from the head back towards the top of the head. Cut
hair against hair growth from the head front to the top
of the head and on the sides. To get a flat top haircut,
use the comb (9): lift the locks and cut them along the
comb. Comb the hair to reveal uneven locks.

CLEANING AND CARE

•
Switch the unit off right after its use by setting
the «0/I» power switch (3) to the «0» position, if
you are using the power adapter (10), discon-
nect it from the mains socket and disconnect
the plug of the power adapter (10) cord from
the socket (1).
•
Remove the installed attachment (7 or 8) from
the unit body and clean the inside and outside
of the attachments (7, 8) from the cut hair, using
the cleaning brush (11).
•
You can wash the attachments (7, 8) under a
water jet, then wipe them dry.
•
Clean the unit body (4) with a soft, slightly damp
cloth, and then wipe it dry.
•
Do not immerse the unit body (4), the power
cord (10) and the power cord plug into water or
any other liquids.
•
Do not use solvents or abrasives to clean the
unit body (4) and attachments (7, 8).
Blade care
Regularly lubricate the blades (5, 6) using the oil
(12) supplied with the unit.
•
Switch the unit off by setting the «0/I» power
switch (3) to the «0» position, if you are using
the power adapter (10), disconnect it from the
mains socket and disconnect the plug of the
power adapter (10) cord from the socket (1).
•
Remove the attachment (7 or 8).
•
Remove the blade block by simultaneously
pressing edges of the blade (5) from the both
sides in the direction from the unit body (4).
MW_2110.indd 10
•
Use the brush (11) to clean the inner part of the
unit body (4) and the blades block from the cut-
off hair.
•
Apply one or two drops of lubricating oil (12) on
the teeth of the blades and the back supporting
part of the upper blade (5).
• Insert the ledge on the lower part of the blades
block into the groove on the body (4), press the
stationary blade (6) from the outer side until the
blade block is fixed. Clicking of the blade block
clamp shows that the blade block is set properly.
•
Turn the hair clipper on and make sure that the
blades are moving smoothly.
•
Switch the unit off and remove the excess lubri-
cating oil from the blades (5, 6) with a dry lint
free cloth.
STORAGE
•
Clean the hair clipper and lubricate the blades
(5, 6) with lubricating oil (12) before taking the
unit away for storage.
•
Keep the unit away from children in a dry cool
place.

DELIVERY SET

Hair clipper – 1 pc.
1.
Attachment combs – 2 pcs.
2.
Power adapter – 1 pc.
3.
Comb – 1 pc.
4.
Cleaning brush – 1 pc.
5.
Lubricating oil – 1 pc.
6.
Scissors – 1 pc.
7.
Instruction manual – 1 pc.
8.

TECHNICAL SPECIFICATIONS

Input voltage of the power adapter:
100-240 V ~ 50/60Hz
Output voltage: DC (direct current) 3 V, 300 mA
The manufacturer reserves the right to change
the specifications of the unit without a preliminary
notification.
Unit operating life is 3 years
Guarantee
Details regarding guarantee conditions can be
obtained from the dealer from whom the appliance
was purchased. The bill of sale or receipt must be
produced when making any claim under the terms
of this guarantee.
This product conforms to the EMC-
Requirements as laid down by the Council
Directive 2004/108/ЕС and to the Low
Voltage Regulation (2006/95/ЕС)
10
25.04.2014 17:27:28