Program My Beverages; General - DeLonghi PrimaDonna S Evo ECAM51 55 Series Instructions For Use Manual

Please note!
The display shows "OK
reaches the minimum programmable quantity.

8.5 Program My beverages

Follow the procedures described in the previous section "8.4
Program beverages" customise the beverages in the
by selecting "Prg. My beverages" from the settings menu, or pro-
ceed with direct programming, as described in section "11. "
Programming and selecting".

8.1 General

Here you can find the settings to customise the basic functions
of the appliance:
1. Press (B2) to enter the "Settings" menu;
2. Press the selection arrows
"General" is displayed between the two dotted lines: press
(B3) to confirm;
3. Press the selection arrows
the required item is displayed between the two dotted
lines, then follow the specific instructions for each setting:
• Set temperature:
To modify the temperature of the water used to make the coffee,
proceed as follows:
4. Press . The current value appears on the display (B1)
and the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B4) or
6. When the required value (low, medium, high, maximum)
has been selected, press
The display goes back to the previous screen.
• Water hardness:
For instructions on identifying and setting water hardness, see
section "16. Setting water hardness".
• Auto-off (standby):
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours
4. Press . The current value appears on the display (B1)
and the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B4) or
6. When the required value (15 min, 30 min, 1 hour, 2 or 3
hours) has been selected, press
The display goes back to the previous screen.
• Energy saving:
To disable or enable "Energy Saving", proceed as follows:
" - (B5) when the length
(B4) or (B5) until
(B4) or (B5) until
(B5);
.
(B5) ;
.
4. Press
tus ("Enabled" or "Disabled"), and the operation to be
performed when confirming with
"Enable?");
5. Press
The display goes back to the previous screen.
Please note!
(B5)
• when the function is enabled, the "ECO" symbol appears on
the display.
"
"
• When in energy saving mode, a few seconds elapse before
the first coffee, cappuccino or milk-based coffee is deliv-
ered as the appliance must heat up again.
• If the milk container (D) is inserted, "Energy Saving" cannot
be activated.
• Beep:
Use this function to enable or disable the beep. Proceed as
follows:
4. Press
tus ("Enabled" or "Disabled"), and the operation to be
performed when confirming with
"Enable?");
5. Press
The display goes back to the previous screen.
• Cup warmer
To warm the cups before making coffee, you can enable the cup
warmer (A11) and rest the cups on the shelf.
4. Press
tus ("Enabled" or "Disabled"), and the operation to be
performed when confirming with
"Enable?");
5. Press
The display goes back to the previous screen.
• Cup lighting
This function enables or disables the cup lighting. The lights
come on each time a coffee or milk-based beverage is made and
during each rinsing cycle.
To disable or enable this function, proceed as follows:
4. Press
tus ("Enabled" or "Disabled"), and the operation to be
performed when confirming with
"Enable?");
5. Press
• Default beverages
Use this function to reset the default values for all the beverag-
es, or the individual beverages programmed previously.
4. Press
that have been customised and the item "All";
36
. The display (B1) shows the current sta-
to disable or enable the function.
. The display (B1) shows the current sta-
to disable or enable the function.
. The display (B1) shows the current sta-
to disable or enable the function.
. The display (B1) shows the current sta-
to disable or enable the function.
(B3). The display (B1) shows the beverages
("Disable?" or
("Disable?" or
("Disable?" or
("Disable?" or