ATTO Technology FastStream SC 5550 Installation And Operation Manual page 66

FCDataRate
(all but SC 8250)
FCDataRate specifies the Fibre Channel data rate at which
operation will occur. Choices are 2Gb/s, 4Gb/s, 8Gb/s or Auto-
negotiated. Note - the FCDataRate displayed in the "info" output
will toggle between 1Gb (5550 only), 2Gb, 4Gb, and 8Gb (8550
only) on 8Gbit-capable hardware if no connection has been
established.
set FCDataRate [fp | all] [2Gb | 4Gb | 8Gb | auto]
get FCDataRate [fp | all]
FCHard
(all but SC 8250)
FCHard enables and disables Fibre Channel hard address
assignment. When FCHard is enabled, the internal hard
address will be used as the loop address on the Fibre Channel
loop. Under soft addressing, the loop address is assigned
during loop initialization.
set FCHard [enabled | disabled]
get FCHard
FCHardAddress
(all but SC 8250)
FCHardAddress specifies the value used as the FC-AL hard
address. This value represents the address that will be used if
hard addressing is enabled. The range of valid Fibre Channel
Hard Address values is 0 through 125.
set FCHardAddress [fp | all] [address]
get FCHardAddress [fp | all]
FCMultiNode
(all but SC 8250)
FCMultiNode determines the reported identity of Fibre Channel
ports. When enabled, each port reports a separate unique Node
Name and logical units may be mapped to either port. When
disabled, each port reports the same Node Name and each
logical unit mapping is applied to all ports.
set FCMultiNode [enabled | disabled]
get FCMultiNode
FCPortErrors
(all but SC 8250)
FCPortErrors displays the number of Fibre Channel errors that
have occurred since the last reboot/power-on or
ResetFcPortErrors.
get FCPortErrors [fp | all]
FCPortList
(all but SC 8250)
FCPortList displays a list of available Fibre Channel ports and
their current status. Valid status values are: Up, Down, Failed,
Reserved, and Disabled.
FCPortList
FCWWName
(all but SC 8250)
FCWWName reports the World Wide Node Name of the Fibre
Channel interface referenced. Each Fibre Channel port has an
individual and unique 8-byte Node Name if the FCMultiNode
setting is enabled.
get FCWWName [fp | all]
FirmwareRestart
FirmwareRestart resets and reinitializes the firmware. Use the
'forced' option to override any CLI reservations held by other
sessions.
FirmwareRestart <forced>
FlashImages
FlashImages displays the metadata for software images
currently stored in the Flash device. The optional parameter
"validate" also validates the CRC of the flash images. Note that
the CRC validation causes a multi-second delay.
FlashImages <validate>
Help
The Help command issued with no parameters displays a list of
available CLI commands. When a CLI Command name is
specified, a command usage string and command description
is presented on the CLI.
Help <command>
HSAdd
HSAdd assigns a Block Device to the Hot Spare pool. Optional
parameter "RAID" and RAID Group name is the ASCII name of
the RAID Group for which to reserve a Dedicated Hot Spare;
this means the Hot Spare is assigned solely to the specified
RAID Group. If no Group name is specified, the Hot Spare is a
global Hot Spare and available for use by any RAID Group.
HSAdd <RAID GrpName> [BlockDevID]
HSDisplay
HSDisplay outputs a list of all of the devices in the Hot Spare
pool.
HSDisplay
HSRemove
Removes a Block Device from the Hot Spare pool.
HSRemove [BlockDevID | all]
IdentifyBridge
IdentifyBridge causes the 'Fault' LED to blink to enable
identification of this system. Disable this option to cancel the
blinking.
set IdentifyBridge [enabled | disabled]
get IdentifyBridge
xvi