Related Manuals for Wampat W07J3062V
Summary of Contents for Wampat W07J3062V
- Page 1 Assembly Instructions W07J3062V Please read this manual carefully before beginning assembly of this product.Keep this manual for future reference.
- Page 4 x 18 x 24 Screw Wooden dowel Cam lock Screw Cam bolt Plastic wedge Ø3.5x14mm Ø15x11mm Ø4x12mm Ø6x33.5mm Ø8x30mm x 14 x 12 Handle bolt Footpads Crash pad Shelf support pin Screw Sticker M4x18mm Ø10x2mm Ø4x35mm Ø8x5x13mm 25x25mm Cam bolt Drawer slider Cam lock Handle...
- Page 5 · Screw cam bolts (A) into panels (1,4,5). ３...
- Page 6 Slider arm Slider arm Slider bracket Slider bracket · Separate the slide bracket from the slide arm as per diagram. · Attach Slider arms to panels (4,5) with screws (D) correctly.
- Page 7 · Insert dowels (B) into Wooden leg (7). · Attach panels (3) to Wooden leg (7), · Insert and secure screw (H) to Wooden leg (7) to lock it.
- Page 8 · Insert dowels (B) into panel (2). · Attach panels (4,5) to panel (2), · Insert and secure cam locks (C) to panel (2) to lock it.
- Page 9 · Insert dowels (B) into panels (4,5). · Then attach panel (3) to panels (4,5) using screws (H). · Stick the skid pad (J) on the bottom of the Wooden leg (7).
- Page 10 · Carefully slide panel (6) into place along the back of the assembly.
- Page 11 · Insert dowels (B) into panels (4,5). · Attach panel (1) to panels (4,5), · Insert and secure cam locks (C) to panels (4,5) to lock it.
- Page 12 · Secure parts (E) to panels (1,3,4,5) using screws (F).
- Page 13 · Attach panels (9,10) to panel (11) with screws (H). · Carefully slide panel (12) into place along the bottom of the assembly.
- Page 14 · Screw Cam bolts (U) into panel (8). · Attach Handle (N) to panel (8) with bolts (G). · Attach panel (8) to panels (9,10). · Insert and secure cam locks (L) to panels(9,10) to lock it.
- Page 15 · Attach slider brackets to panels (9,10) with screws (D) correctly. · Stick part (K) on panels (8) correctly.
- Page 16 · Attach part (O) to panels (13) with screws (D) correctly. · Attach part (N) to panels (13) with bolts (G) correctly.
- Page 17 Warning： follow the next step to adjust the crack of the doors . 警告 : 次の手順に従ってドア の隙間を調整します。 · Attach part (13) to panel (5) with screws (D) correctly. · Stick part (K) on panels (13) correctly. · Stick stickers (I) on screw (H).
- Page 18 Warning： open the doors and adjust the right hinge follow the picture 1 and 2 ，and the side crack of the doors is about 1mm） 警告 : ドアを開けて、図1と図2に従って 右のヒンジを調整します。ドアの 側面の隙間は約1ミリ。...
- Page 19 Adjust Height / 高さを調節 Adjust front and back / 前後を調節 Adjust Left and right / 左右を調節...
- Page 20 · Insert the shelf supports(L) at the desired level and place the adjustable shelves(14) onto the shelf supports.
- Page 21 · Stick stickers (I) on cam locks (C,M). Slider arm x 10 Slider bracket · Assembled the drawers as per diagram Note :If the drawer does not go in smoothly. Press or lift the plastic release lever. Pull out the slider bracket from the slider arm then re-assembled the drawer until they were going in smoothly well.
- Page 22 WARNING Serious or fatal injuries can occur from furniture tipping over. To prevent the furniture from tipping over we recommend that it is permanently fixed to the wall. Wall anchor and hardware are included with this product. Please make sure hardware is suitable for your walls before installing, as different wall materials may require different types of anchors.