Advertisement
Quick Links
Part List:
Header Assembly - Qty 1
Driver Side Over Door Bow - Qty 1
Passenger Side Over Door Bow - Qty 1
Center Bow Assembly - Qty 1
Center Bow Legs- Qty 2
Driver's Side Door Surround - Qty 1
Passenger Side Door Surround - Qty 1
Door Surround Knobs - Qty 4
Roll Bar Bow Mount Brackets - Qty 2
M6x20 Torx Bolts- Qty 4
Rear Bow Legs- Qty 2
Rear Bow- Qty 1
Tailgate Bar- Qty 1
Tailgate Bar Brackets- Qty 2
This Replacement hardware kit is designed to fit on your 2 Dr Jeep® Wrangler when the original soft
top or hard top has been completely removed. Before beginning your installation of this product,
NOTICE
you will need to remove your existing soft top fabric, hardware or Hard top.
Loss of vehicle control involves risk of death or serious injury, particularly to parts of your body not
restrained within vehicle. This product is intended for weather protection only and should not be relied
upon to contain occupants in the event of an accident or to protect from either ground contact or
falling objects. To reduce risk of accident or injury:
•
ALWAYS WEAR SEATBELTS
WARNING
•
Always keep head, arms & body parts within vehicle.
•
Fully secure or stow the soft top before driving according to instructions. Never try to latch or fold
soft top while driving. Do not use if damaged or worn.
•
Read and follow all instructions & warnings accompanying this product, in your vehicle owner's
manual and Off Road Driving Supplement.
RISK OF EYE INJURY. Safety glasses should be worn at all times while installing or maintaining this
CAUTION
product.
Installation Instructions
Replacement Soft Top Hardware for 2007-2018
2 Door Jeep
®
Item
15433301
#
Required Tools:
Safety Glasses
Phillips Screw Driver
Flat Head Screw Driver
T-20 Torx Driver
Wrangler JK
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MasterTop 15433301
Summary of Contents for MasterTop 15433301
- Page 1 Installation Instructions Replacement Soft Top Hardware for 2007-2018 2 Door Jeep ® Wrangler JK Item 15433301 Part List: Header Assembly - Qty 1 Required Tools: Driver Side Over Door Bow - Qty 1 Safety Glasses Passenger Side Over Door Bow - Qty 1...
- Page 2 Important Safety information Your MasterTop® Replacement hardware is intended to be used with other MasterTop Products to increase the fair weather enjoyment of your off-road capable vehicle. Before installation, please take a moment to review the following safety information and installation instructions. Important safety information is generally preceded by one of three signal words indicating the relative risk of injury.
- Page 3 JK Soft Top Hardware Installation Step 1: Install Bow Mount Brackets to Roll Bar FIG 9 FIG 10 Locate the (2) bow mounting brackets and (4) Torx head pivot bracket bolts shown in FIG 9. Carefully unzip the roll bar padding on the vertical side tube to expose the two factory holes in the roll bar (FIG 10).
- Page 4 Step 3: Pillar and Over Door Surround Assembly FIG 18 Locate the driver’s side Rear over door assembly and the driver’s side Pillar assembly shown in FIG18. Turn the two pieces over as shown in FIG19 and line up the slot on the pillar assembly with the “T”...
- Page 5 Step 5: Install Door Surrounds to Jeep Locate the assembled Driver’s side rear door surround On the bottom of the vertical pillar portion of the assembled door surround is a pin that will be inserted into the body tub as shown in FIG 25. Insert the door surround pin into the body tub.
- Page 6 FIG 41 FIG 42 Step 9: Install Over Door Bows to Center Locate the two over door bows as called out in FIG 41. The over door Bow legs should fit inside the Door FIG 44 FIG 43 surrounds(Figs 42 & 43) with the Quick release knob facing out.
- Page 7 FIG 54 Step 10 Continued: Install Rear Bow Legs to Bow Mounts and Rear Bow With the two Rear Bow Legs installed to the Bow mount Bracket, locate the rear bow called out in FIG 54. On the Bow leg there is a set screw that needs to FIG 55 be removed.
- Page 8 Step 12: Attaching the Tailgate bar Brackets FIG 65 Locate the Tailgate bar and brackets (FIG 65). Locate the driver’s side bracket (marked on the bracket) with the lip to the outside of the vehicle, line up the bracket with the slot in the body tub, hook the rear portion of the bracket to the body tub and roll the bracket forward until it clicks.
Need help?
Do you have a question about the 15433301 and is the answer not in the manual?
Questions and answers