Subscribe to Our Youtube Channel
Related Manuals for ESAB Origo Mig 320
Summary of Contents for ESAB Origo Mig 320
- Page 1 Origo™ Mig 320 Instruction manual 0463 274 001 GB 20120822 Valid for serial no. 626-xxx-xxxx, 121-xxx-xxxx...
- Page 2 - 2 -...
-
Page 3: Table Of Contents
1 SAFETY ............2 INTRODUCTION . -
Page 4: Safety
SAFETY Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be ob... - Page 5 A equipment in those locations, due to conducted as well as radiated disturbances. CAUTION Read and understand the instruction manual before installing or operating. CAUTION This product is solely intended for arc welding. - 5 - ba51e © ESAB AB 2011...
-
Page 6: Introduction
As the person responsible for the equipment, it is your responsibility to obtain information on approved collection stations. For further information contact the nearest ESAB dealer. ESAB can provide you with all necessary welding protection and accessories. INTRODUCTION The Mig 320 is a step switched power source designed for MIG/MAG−welding together with wire feed units Feed 302 and Feed 304. -
Page 7: Technical Data
This product is intended for industrial use. In a domestic environment this product may cause radio interference. It is the user's responsibility to take adequate precautions. Location Position the welding power source in such way that its cooling air inlets and outlets are not obstructed. - 7 - ba51e © ESAB AB 2011... -
Page 8: Assembly Of Components
Assembly of components WARNING During transport, the rear wheels of the power source are in their forward position. Before use, place the wheels in their rear position. - 8 - ba51e © ESAB AB 2011... -
Page 9: Assembly Of Stabilizer
Assemble the stabilizer if a counter balance is to be installed on machine. The stabilizer is an accessory. The order number can be found on page 19. Attention! Use of a counter balance without stabilizer may cause the machine to tip over. Electrical installation - 9 - ba51e © ESAB AB 2011... -
Page 10: Mains Power Supply
NB: The mains cable areas and fuse sizes as shown above are in accordance with Swedish regulations. They may not be applicable in other countries: make sure that the cable area and fuse sizes comply with the relevant national regulations. - 10 - ba51e © ESAB AB 2011... -
Page 11: Operation
Connection for control cable for wire feeder Orange indicator lamp, overheating Digital instrument V/A Overheating protection A thermal overload cutout protects against overheating. The cutout resets automatically when the unit has cooled. - 11 - ba51e © ESAB AB 2011... -
Page 12: Inductance Connection
Otherwise the air inlet/outlet may become blocked and cause overheating. To avoid this you can use an air filter. The air filter is an accessory. Ordering number can be found on page 19. - 12 - ba51e © ESAB AB 2011... -
Page 13: Fault Tracing
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. - 13 - ba51e ©... -
Page 14: Diagram
Diagram Mig 320, 400 V - 14 - © ESAB AB 2011 ba51e... - Page 15 - 15 - © ESAB AB 2011 ba51e...
- Page 16 Mig 320, 230-500V - 16 - © ESAB AB 2011 ba51e...
- Page 17 - 17 - © ESAB AB 2011 ba51e...
-
Page 18: Order Number
0349 312 600 Origo™ Mig 320 230/400-415/500 V, 3~50Hz , 230/400-460 V, 3~60Hz with digital instrument 0349 300 522 Origo™ Mig 320 Spare parts list Technical documentation is available on the Internet at www.esab.com - 18 - ba51o © ESAB AB 2011... -
Page 19: Accessories
Cable holders ......0349 303 362 - 19 - ba51a © ESAB AB 2011... - Page 20 Stabilizer ....... 0349 303 475 - 20 - ba51a © ESAB AB 2011...
- Page 21 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 21 - notes...
- Page 22 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 22 - notes...
- Page 23 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 23 - notes...
- Page 24 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...
Need help?
Do you have a question about the Origo Mig 320 and is the answer not in the manual?
Questions and answers