ESAB Aristo Origo Mig C3000i Instruction Manual
Hide thumbs
Also See for Aristo Origo Mig C3000i:
- Instruction manual (24 pages) ,
- Service manual (106 pages)
Subscribe to Our Youtube Channel
Related Manuals for ESAB Aristo Origo Mig C3000i
Summary of Contents for ESAB Aristo Origo Mig C3000i
- Page 1 Aristo®, Origo™ Mig C3000i Instruction manual Valid for: serial no. 039-, 209-xxx-xxxx 0459 825 301 GB 20180918...
-
Page 3: Table Of Contents
Changing feed rollers ................MAINTENANCE ................... Inspection and cleaning ................. TROUBLESHOOTING ................. ORDERING SPARE PARTS ................ DIAGRAM ......................ORDERING NUMBERS ..................22 WEAR PARTS ...................... ACCESSORIES ....................25 Rights reserved to alter specifications without notice. 0459 825 301 © ESAB AB 2018... -
Page 4: Safety
Safety Data Sheets (SDSs). Safety precautions Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace. - Page 5 Protect your eyes and body. Use the correct welding screen and filter lens and wear protective clothing. • Protect bystanders with suitable screens or curtains. NOISE - Excessive noise can damage hearing Protect your ears. Use earmuffs or other hearing protection. 0459 825 301 - 5 - © ESAB AB 2018...
- Page 6 For further information contact the nearest ESAB dealer. ESAB has an assortment of welding accessories and personal protection equipment for purchase. For ordering information contact your local ESAB dealer or visit us on our website. 0459 825 301 - 6 - ©...
-
Page 7: Introduction
It is also possible to weld with coated electrodes (MMA welding). The power sources comes in different variants, see chapter "ORDERING NUMBERS". ESAB accessories for the product can be found in the "ACCESSORIES" chapter of this manual. Equipment The welding power source is supplied with: •... -
Page 8: Technical Data
Open-circuit voltage U MIG/MAG without VRD function 70 - 80 V 57 - 67 V MMA without VRD function 60 V VRD function deactivated < 35 V VRD function activated 0459 825 301 - 8 - © ESAB AB 2018... - Page 9 Equipment marked IP23 is intended for indoor and outdoor use. Application class The symbol indicates that the power source is designed for use in areas with increased electrical hazard. 0459 825 301 - 9 - © ESAB AB 2018...
-
Page 10: Installation
A protective earth connection must be made in accordance with regulations. Rating plate with supply connection data 0459 825 301 - 10 - © ESAB AB 2018... - Page 11 This welding power source is designed for connection to a four wire 230/400 volt system. If the power source is to be used in a country with a higher mains voltage, the power source shall be connected via a safety transformer. 0459 825 301 - 11 - © ESAB AB 2018...
-
Page 12: Operation
Rotating parts can cause injury, take great care. WARNING! Risk of crushing when replacing the wire bobbin! Do not use safety gloves when inserting the welding wire between the feed rollers. 0459 825 301 - 12 - © ESAB AB 2018... - Page 13 5 OPERATION 0459 825 301 - 13 - © ESAB AB 2018...
-
Page 14: Connections And Control Devices
When this occurs the welding current is interrupted and a fault code is displayed on the control panel. The overheating protection resets automatically when the temperature has fallen. 0459 825 301 - 14 - © ESAB AB 2018... -
Page 15: Welding Without Gas
When you hold the welding torch approx. 5 mm from the piece of wood (figure A) the feed rollers should slip. If you hold the welding torch approx. 50 mm from the piece of wood, the wire should be fed out and bend (figure B). 0459 825 301 - 15 - © ESAB AB 2018... -
Page 16: Replacing And Inserting Wire
During installation, repeat the above in the reverse order. Choice of tracks in the feed rollers Turn the feed roller with the dimensioning mark for the required track towards you. 0459 825 301 - 16 - © ESAB AB 2018... -
Page 17: Maintenance
Cleaning and replacement of the welding torch's wear parts should take place at regular intervals in order to achieve trouble-free wire feed. Blow the wire guide clean regularly and clean the contact tip. 0459 825 301 - 17 - © ESAB AB 2018... -
Page 18: Troubleshooting
Check that the welding current supply and return cables are correctly connected. • Check that the correct current value is set. • Check that the correct wire is being used. • Check the mains power supply fuses. 0459 825 301 - 18 - © ESAB AB 2018... -
Page 19: Ordering Spare Parts
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see esab.com. When ordering, please state product type, serial number, designation and spare part number in accordance with the spare parts list. -
Page 20: Diagram
DIAGRAM DIAGRAM 0459 825 301 - 20 - © ESAB AB 2018... - Page 21 DIAGRAM 0459 825 301 - 21 - © ESAB AB 2018...
-
Page 22: Ordering Numbers
0458 818 990 Spare parts list ® Control panel Aristo 0458 870 201 Instruction manual Welding torch PSF 305, 4,5 m Instruction manuals and the spare parts list are available on the Internet at: www.esab.com 0459 825 301 - 22 - © ESAB AB 2018... -
Page 23: Wear Parts
In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be used. It is recommended to use 3 m long welding torch for aluminium wire, equipped with appropriate wear parts. 0459 825 301 - 23 - © ESAB AB 2018... - Page 24 WEAR PARTS 0459 825 301 - 24 - © ESAB AB 2018...
-
Page 25: Accessories
0459 491 883 Remote control unit AT1 CAN MMA and TIG: current 0459 491 884 Remote control unit AT1 CF CAN MMA and TIG: rough and fine setting of current. 0459 825 301 - 25 - © ESAB AB 2018... - Page 26 0458 400 898 0458 400 899 400 A 100% 350 A 100% 0.8 - 1.6 = Self cooled = Smoke exhausters, Centrovac = Smaller, Light duty = Water cooled RS3 = 3-step program switch for selecting preset programs. 0459 825 301 - 26 - © ESAB AB 2018...
- Page 27 ACCESSORIES 0459 825 301 - 27 - © ESAB AB 2018...
- Page 28 For contact information visit esab.com ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone +46 (0) 31 50 90 00 http://manuals.esab.com...
Need help?
Do you have a question about the Aristo Origo Mig C3000i and is the answer not in the manual?
Questions and answers