Ovation PIONEER 100C ZOOM User Manual

100w rgbw led fresnel with zoom

Advertisement

Quick Links

PIONEER 100C ZOOM
100W RGBW LED fresnel with zoom
USER MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PIONEER 100C ZOOM and is the answer not in the manual?

Questions and answers

Summary of Contents for Ovation PIONEER 100C ZOOM

  • Page 1 PIONEER 100C ZOOM 100W RGBW LED fresnel with zoom USER MANUAL...
  • Page 2: Table Of Contents

    Table of contents Caution! ������������������������������������������������������������������������������������������������������������������������������������������������ 3 Introduction ������������������������������������������������������������������������������������������������������������������������������������������ 3 Safety instructions ������������������������������������������������������������������������������������������������������������������������������� 3 Overview ���������������������������������������������������������������������������������������������������������������������������������������������� 3 Installation ������������������������������������������������������������������������������������������������������������������������������������������� 4 Read ‘Safety information’ before installing the fixture.................4 Fastening the fixture to a flat surface ......................4 Mounting the fixture on a truss ........................5 Securing with a safety cable .........................5 DMX-512 connection/connection between fixtures ..................5 Power connection ............................6...
  • Page 3: Caution

    - download the latest version of the user manual from the Internet Introduction Thank you for having chosen Pioneer 100C zoom. You will see you acquired a powerful and versatile de- vice. Unpack your item. Before you initial start-up, please make sure that there is no damage caused by trans- portation.
  • Page 4: Overview

    Overview Installation Read ‘Safety information’ before installing the fixture. The fixture is designed for indoor use only and must be used in a dry location with adequate ventilation. Ensure that none of the fixture’s ventilation slots are blocked. Fasten the fixture to a secure structure or surface. Do not stand it on a surface or leave it where it can be moved or fall over.
  • Page 5: Mounting The Fixture On A Truss

    you install the fixture in a location where it may cause injury or damage if it falls, secure it as directed be- low with a securely anchored safety cable that will hold the fixture if the primary fastening method fails. Mounting the fixture on a truss The fixture can be clamped to a truss or similar rigging structure in any orientation.
  • Page 6: Power Connection

    Earth(Ground) Operation The Pioneer 100C zoom can operate in different modes. In each mode you can run the fixture as a stand alone fixture or in a master/slave confiugration. This next section will detail the differences in the operat- ing modes.
  • Page 7: Addressing

    In the case of the Pioneer 100C zoom, which is 3/4/5/6/12 channels fixture. If you set, for example, the address in the 3 channel mode to channel 4, the device will use the channel 4 to 7 for control.
  • Page 8: Dmx Protocol

    isting non-RDM equipment. It allows a console or dedicated RDM controller to send commands to and receive messages from specific fixtures. With RDM function, you can set the DMX address of your fixtures remotely. This is especially useful when the device is installed in a remote area. Each Pioneer 200 zoom has a factory set RDM UID (unique identification number).
  • Page 9 12 Channels Mode Function Function Control 000-020: no function 021-030: Auto1 031-040: Auto2 041-050: Auto3 051-060: Auto4 061-070: Auto5 Auto program 071-080: Auto6 081-090: Auto7 091-100: Auto8 101-110: Auto9 111-120: Auto10 121-255: No function CH10 Auto program speed 000-255: Speed increasing 000-005: Menu setting 006-055: Dimmer speed 0 (no delay) 056-105: Dimmer speed 1...
  • Page 10: Id Address Selection(Stag-12 Channels Mode)

    4 Channels Mode Function Function Control Dimmer 000-255: 0-100% dimmer 000-255: 0-100% Red dimmer Green 000-255: 0-100% Green dimmer Blue 000-255: 0-100% Blue dimmer ARC�2 4 Channels Mode Function Function Control 000-255: 0-100% Red dimmer Green 000-255: 0-100% Green dimmer Blue 000-255: 0-100% Blue dimmer White...
  • Page 11: Fixture Cleaning

    DMX value Function DMX value Function DMX value Function 000-009 ID1-ID66 ID23 ID46 010-019 ID24 ID47 020-029 ID25 ID48 030-039 ID26 ID49 040-049 ID27 ID50 050-059 ID28 ID51 060-069 ID29 ID52 070-079 ID30 ID53 080-089 ID31 ID54 090-099 ID32 ID55 100-109 ID10 ID33...
  • Page 12: The Fixture Does Not Work, No Light

    Check the connection of power and main fuse. Be sure the external fuse has not blown. • Measure the mains voltage on the main connector. Technical specifications Model Pioneer 100C zoom Power supply: AC100-240V, 50/60Hz Light source: 100W LED Color mixing:...

Table of Contents