Ovation CTC 300 FRESNEL User Manual

300w led fresnel with zoom

Advertisement

Quick Links

CTC 300 FRESNEL
300W LED fresnel with zoom
USER MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CTC 300 FRESNEL and is the answer not in the manual?

Questions and answers

Summary of Contents for Ovation CTC 300 FRESNEL

  • Page 1 CTC 300 FRESNEL 300W LED fresnel with zoom USER MANUAL...
  • Page 2: Table Of Contents

    Table of contents Caution! ������������������������������������������������������������������������������������������������������������������������������������������������ 3 Introduction ������������������������������������������������������������������������������������������������������������������������������������������ 3 Safety instructions ������������������������������������������������������������������������������������������������������������������������������� 3 Overview ���������������������������������������������������������������������������������������������������������������������������������������������� 4 Installation ������������������������������������������������������������������������������������������������������������������������������������������� 5 Read ‘Safety information’ before installing the fixture................5 Fastening the fixture to a flat surface ......................5 Mounting the fixture on a truss ........................5 Securing with a safety cable ........................5 DMX-512 connection/connection between fixtures ..................6 Power connection ............................6...
  • Page 3: Caution

    - download the latest version of the user manual from the Internet Introduction Thank you for having chosen CTC 300 Fresnel. You will see you acquired a powerful and versatile de- vice. Unpack your item. Before you initial start-up, please make sure that there is no damage caused by transportation.
  • Page 4: Overview

    Overview Yoke Accessories clip Barn door and color frame holder Yoke locking knob LCD display Safety cable anchor point Handle On/off Rotary and Enter switch button Fuse Power Power Dmx in Dmx out 5-pin 5-pin Dmx signal indicator LCD display Power indicator Menu Down...
  • Page 5: Installation

    Installation Read ‘Safety information’ before installing the fixture. The fixture is designed for indoor use only and must be used in a dry location with adequate ventilation. Ensure that none of the fixture’s ventilation slots are blocked. Fasten the fixture to a secure structure or surface. Do not stand it on a surface or leave it where it can be moved or fall over.
  • Page 6: Dmx-512 Connection/Connection Between Fixtures

    Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture. Power connection Power Requirements The CTC 300 Fresnel zoom luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The lumi- naire contains an auto-ranging power supply. Power linking between fixtures: www.hotion.com...
  • Page 7: Operation

    Earth(Ground) Operation The CTC 300 Fresnel zoom can operate in three different modes. In each mode you can run the fixture as a stand alone fixture or in a master/slave confiugration. This next section will detail the differences in the operating modes.
  • Page 8: Control Menu

    Signal Hold On/Off Run if signal cut On/Off RDM function on/off Screen Timeout Display shut off time Never Screen Brightness 25 - 100% Display brightness Dimming Freq 1.20 - 24.0 KHz Dimmer frequency setting Software Version Vx.xx Software version Reset Yes/No System reset Reverse...
  • Page 9: Universal Dmx Control

    In the case of the CTC 300 Fresnel zoom, which is 3/6 channels fixture. If you set, for example, the ad- dress in the 3 channel mode to channel 4, the device will use the channel 4-6 for control.
  • Page 10: Rotary Knob Function

    Note: Before operation, enable RDM function in Advanced settings. Rotary Knob function The knob in the rear panel of the CTC 300 Fresnel act as multi function. Including rotary control of dimmer, rotary control of dimmer, up/down/enter function function. Dimmer & strobe function: 1.
  • Page 11: Set Dimmer Curves

    Temp - 034 ℃ Temp - 034 ℃ Signal Hold - On Signal Hold - On Fan Spee d Fan - Sm art Fan Spee d Fan - Sm art 1800 (RPM) Mode - S tandard 1800 (RPM) Mode - S tandard Brightness Brightness Zoom...
  • Page 12: Dmx Protocol

    To set preset dimmer curves: 1. Press the MENU button to enter the main menu. 2. Press the UP or DOWN button to select Dimmer menu and press ENTER. 3. Press DOWN menu and select Mode sub menu. 4. Select disired dimmer mode. Custom dimmer curves: 1.
  • Page 13: Fuse Replacement

    Check the connection of power and main fuse. Be sure the external fuse has not blown. • Measure the mains voltage on the main connector. Technical specifications Model CTC 300 Fresnel Power supply: AC100 - 240V, 50/60Hz Light source: 300W COB LED...
  • Page 14 G.W.: 13kg(28.7lb) Accessories(included): Power lead, Safety rope, Gel frame Accessories(optional): Clamp Enviroment: IP20 Please note: All information is subject to change without prior notice� 11�12�2021 www.hotion.com...
  • Page 15 www.hotion.com...
  • Page 16 www.hotion.com...

Table of Contents