Advertisement
Quick Links
IMPERA
INSTALLATION AND SET UP GUIDE
INSTALLATION CONSIDERATIONS
• The Connect-X MP6 is an extension device that provides serial, IR, GPIO ports, as
well as LAN control.
• The device may be installed in various locations using the built-in mounting system
that allows the device to be securely fastened on or under desktops, on walls,
equipment racks, or tied to cables, etc.
• PoE powered: use an IEEE 802.3 - compliant PoE power supply of switch. PoE
injector is not included.
INCLUDED IN THE BOX
Biampinfo@biamp.com
CONNECT - X MP6
EXTENSION DEVICE
www.biamp.com
Advertisement
Related Manuals for Biamp IMPERA CONNECT-X MP6
Summary of Contents for Biamp IMPERA CONNECT-X MP6
- Page 1 • PoE powered: use an IEEE 802.3 - compliant PoE power supply of switch. PoE injector is not included. INCLUDED IN THE BOX Biampinfo@biamp.com www.biamp.com...
- Page 2 DEVICE LAYOUT FRONT PANEL LAYOUT FRONT PANEL INDICATORS 1. 1 Power LED indicator 2. 1 Status LED indicator REAR PANEL LAYOUT REAR PANEL PORTS AND TERMINALS 1. 1 RJ-45 Network (LAN) port with PoE functionality 2. 1 Factory reset recessed pin-hole button 3.
- Page 3 INSTALLATION OPTION 1 Install on a flat surface using the screw hole mounts. These allow for the device to be mounted in a varity of locations such as under a table or on a wall. 1. Determine the location where the device will be located and verify the surface is flat enough for the device to be mounted.
- Page 4 INSTALLATION 3. Loop the pointed end of the zip tie around what the device will be secured to and then back through the guide slot. 4. Insert the the pointed end of the zip tie into the locking mechanism until it clicks.
- Page 5 POWER AND STATUS INDICATORS POWER LED INDICATOR Off: Green: The device is not The device is powered powered STATUS LED INDICATOR Off: The device is not powered Flashing Green: Solid Green: No errors Device is powering Solid Amber: Flashing Amber: Firmware version Factory reset in different than...
- Page 6 CONNECTIONS RS - 232 / IR TERMINALS The TX and RX termials can be configured as either RS-232 or IR emitter ports using the Biamp Project Designer software. One-Way Communicatons: The TX-3 and TX-2 are unidriectional transmit terminals. Two-Way Communications: The TX-1 and RX-1 terminals make up a bidirectional transmit and receive terminal.
- Page 7 CONNECTIONS RS-232 unidirectional transmit port example. Ground to Pin 5 Tx-2 to Pin 2 Single IR port unidirectional transmit example. IR Emitter Ground to IR Emitter Tx-2 striped wire to IR Emitter Installation & Set Up Guide...
- Page 8 CONNECTIONS Dual IR port example. IR 2 Emitter Junction IR 1 Emitter Ground to IR 2 Emitter TX-2 to IR 1 Emitter Installation & Set Up Guide...
- Page 9 CONNECTIONS INPUT / OUTPUT PORTS ( I/O ) The controller has 3 general ports that are each configured as either output or input. Each of these I/O ports is available for connection to devices such as: • A PIR movement sensor •...
- Page 10 CONNECTIONS ETHERNET PORT ( LAN ) The RJ-45 Network (LAN) connector with PoE functionality is used for: • Power over Ethernet • Connecting to a host controller • Configuring and controlling third-party devices over a network Port LED indicators: The yellow LED indicates the link status and the green LED indicates the link speed.
- Page 11 CONNECTIONS LAN Networking Features • DHCP client - Obtain a network IP addresss from a DHCP server • HTTPS client - Control third-party devices through HTTPS • IGMP v2 - Filter out unneeded multicast network traffic • NTP client - Obtain a real-time from an NTP server •...
- Page 12 Support@biamp.com 9300 SW Gemini Drive Beaverton, OR 97008 USA Warranty: Biamp.com/legal/warranty-information Safety & Compliance: biamp.com/compliance May 25, 2023...
Need help?
Do you have a question about the IMPERA CONNECT-X MP6 and is the answer not in the manual?
Questions and answers