Hyundai 12ESH Operation Manual page 43

fork-lift truck , stride- truck and platform carrying vehicle) moves, the load surface must be in a upgrade
direction.
F) When the truck works on various slopes, the load and the load bearing device must tilt backward (if
possible), and the driver can only elevate the load's height that is enough for running through the road
surface and local barrier.
14.2.3.4 Get across a gap
It must be ensured that under hanging devices (such as: lamps, pipeline and fire extinguishing system) there
is an enough clearance height.
Before getting across the passage and door, it must be ensured that there is an enough gap among the vehicle,
the driver and the load.
14.2.3.5 Working in road truck and railroad vehicle
Before a motor-driven industry truck runs on (or run down) the road vehicle or railroad vehicle, some
necessary measures must be taken to prevent road truck and railroad vehicle from moving.
Before a semi- trailer that is not linked with a tractor runs on the road truck or railroad truck, it must be
ensured that the supporting part of the stilt of the semi- trailer is located at the supporting position.
Before a motor-driven industry truck runs on the road vehicle or railroad vehicle, it must be ensured that the
floor board can endure all the weight of the industry vehicle, load and the driver. Besides, it is required to
check the plank to see if there are crashes, holes or other damages.
When the industry truck works on high place or platform, it is forbidden to move other truck by industry truck.
It is also prohibited to close railroad truck's door by industry truck except for one case that the industry truck
is equipped with a special device and the driver has also been trained how to use this device.
If possible, the truck should cross over the railway virgule.
14.2.3.6 The truck operating on the gangplank or transition board
Before the motor industrial vehicle pass the gangplank or transition board, it is necessary to make sure the
firm of the board.
The overall weight of the truck should not excess the rated capacity of the gangplank or the transition board.
When passing the gangplank or the transition board, the driver should drive the truck carefully and slowly.
14.2.3.7 The use of the truck in elevator (lifter)
Before the motor industrial vehicle driving into the elevator (lifter), it is necessary to make sure the elevator
(lifter) can endure the over all weight of the truck, load and drivers.
Before allow the truck driving in or out of the elevator (lifter), all other personnel should leave away from the
elevator (lifter).
After the bridge box floor of the elevator (lifter) is even to the ground, the truck should slowly drive in as the
positive direction.
It should be the load go into the elevator (lifter) first not the driver, this is specially adapted to the walking type
truck.
After the truck driving into the elevator (lifter), it is necessary to put the control device in the central position.
Switch off the power, and tighten the brake.
14.2.3.8 Parking
After the driver leaving, the carrying device must lower to the lowest position, put the control device to the
central position, switch off the power, and tighten the brake, stay steady the vehicle to prevent accidental
move or make bold by others without approval.
When parking the truck, the fire fighting passage, access stairs and fire fighting passages should keep fluently.
The parking location of the truck should keep a safety distance to the railway.
14.2.4 The vehicle maintaining rule for the drivers
14.2.4.1 General rule
Before starting the truck, it is necessary to inspect the technical condition of the truck. According to the
different type of the truck, should pay more attention to some special location: [for example: fuel oil system,
alarm system, power system, brake, steering equipment, lighting, wheel and air tire pressure (namely gas filled
type) and lifting system (including lifting chain, wire rope, limit switch and hydraulic cylinder).
If the truck is found to be repaired, or during the operation the defect develops, it is necessary to report it
to the superior in concern. It is forbidden to repair or adjust the truck by the truck by the driver without
permission.
The truck which fuel oil system is leaking could not be uses without repair.
14.2.4.2 Refuel
Before refuel, it is necessary to close the engine, brake the truck and the driver should leave the truck.
The open flame and smoking is forbidden during refueling.
14.2.4.2.1 Liquid fuel (for example gasoline and diesel fuel)
The truck using liquid fuel should add fuel in the appointed places.
Before take away the refueling equipment, cover the filler cap and clear up the excessive fuel, the engine
39