Hyundai 12ESH Operation Manual page 41

Electric stacker
Table of Contents

Advertisement

The motor industrial vehicle could not carry passengers, except for equipped with the facility for the
passengers sitting.
The driver should pay special attention to the operating circumstance, including the person nearby other
staves and fixed or moving substances, and it is necessary to watch out for the passerby at any moment.
No matter whether there is load on the lifting part of the truck, it is forbidden anyone passing or standing
under the lifting part of the truck.
If the people, building, organization or equipment accident happens, it is necessary to report to the relevant
officer at once.
The driver should not change, add or demolish the truck components without the permission toinfluence the
performance of the truck .It is not allowed to install accessorial frame or handle on the steering wheel ,except
the factory has installed it.
The driver should use the truck in the using range. When operating high stacking job, convey high and
multi-piece piled goods using driving type high-lift truck, it is necessary to use the truck with blind goods shelf
and canopy guard shelf.
Exception: if there is no danger of the load fall down on the driver, the truck without blind goods shelf can
be used.
When operating high stacking job, convey high and multi-piece piled goods using walking type truck, the blind
goods shelf is necessary.
14.2.2
Load carriage (lifting and stacking) rule
14.2.2.1
Load
The industrial truck or the combination of the industrial truck and attachment only can convey the load not
over its rated load weight. The capacity of the industrial truck with attachment maybe less than the one
marked on the nameplate.
Any measure of enhancing the capacity of the truck is forbidden, for example the adding people or balance
weight.
In any conditions, especially when using the attachment, it is necessary to pay attention to the operation,
location, fixation and transportation of the load. The truck with attachment when unloaded should be treated
as with some capacity.
Only the rank stabilized or safety load can be conveyed, especially when convey the super long or high load,
should pay special care.
When convey the load which center of gravity is uncertain, operating the vehicle should special carefully.
14.2.2.2
The loading and unloading of goods.
When loading the goods with forks:
A) The space between the forks should fit the width of the conveying load.
B) The fork should insert into the inner of the load as deep as possible. But pay attention to not make the
fork tip touch the substance except the load. Then the fork should lift to the enough height to move the
goods.
C) When conveying high and multi-piece piled goods, it is necessary to tilt the mast back ward a little (if can
tilt back) to stabilize the load, and should be careful specially.
When unloading the goods, it is necessary to descend carefully. If possible, tilt the mast forward
(or limited)in order to put ready the load and draw out the fork.
14.2.2.3
Stacking
When stacking, the mast should tilt backward to ensure the stability of the load, approach the goods pile
slowly.
When the truck approach and face to the goods pile, it is necessary to adjust the mast to the vertical location,
and lift the load a little higher than the height of the pile. Then running backward the truck or if using reach
truck, extends the fork and descend it to unload the goods.
After lifting, start the vehicle, no matter with or without load, it is necessary to operate the brake carefully and
placidly.
It is necessary to ensure that the stacking is firm.
After stacking, draw off the fork, and lower the fork to the operating height. After confirm there is no block
on the road, drive away the truck.
As for truck can tilt backward, it is necessary to use this function to stabilize the load.
14.2.2.4
Unpiling
The truck approaches the pile slowly, and stopped when the fork tip is 0.3 m far away from the pile.
The space of the fork should adjusted to the width of the conveying load, and should check the weight of the
load, to make sure the load is in the lifting weight range of the truck.
It is necessary to lift the fork vertically and insert it to the bottom of the goods.
After lifting, start the truck, no matter the truck with or without load, it is necessary to operate the brake
carefully and placidly.
37
a little

Advertisement

Table of Contents
loading

Table of Contents