Related Manuals for HP JG726A
Summary of Contents for HP JG726A
- Page 1 HP FlexFabric 5930 Switch Series Installation Guide Part number: 5998-7149 Document version: 6W101-2015020...
- Page 2 The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
-
Page 3: Table Of Contents
Contents Preparing for installation ············································································································································· 1 Safety recommendations ·················································································································································· 2 Examining the installation site ········································································································································· 2 Temperature/humidity ············································································································································· 3 Cleanliness ································································································································································ 3 EMI ············································································································································································· 3 Laser safety ································································································································································ 4 Installation tools ································································································································································· 4 ... - Page 4 Fan tray alarm LEDs ·············································································································································· 62 Appendix D Cooling system ······································································································································ 63 HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA and HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA cooling system ································································································································································ 63 HP 5930-4Slot/HP 5930-4Slot TAA cooling system ································································································· 64 ...
-
Page 5: Preparing For Installation
For regulatory identification purposes, the HP FlexFabric 5930-32QSFP+ Switch and HP FlexFabric 5930-32QSFP+ TAA Switch are assigned Regulatory Model Numbers (RMNs). The RMNs for these products are listed below. These regulatory numbers should not be confused with the marketing name HP FlexFabric 5930, or the product codes JG726A and JG727A. -
Page 6: Safety Recommendations
HP FlexFabric 5930, or the product codes JH178A, JH187A, JH179A, and JH188A. Product code Description JH178A BJNGA-AD0049 HP FF 5930-2Slot+2QSFP+ Switch JH187A BJNGA-AD0049 HP FF 5930-2Slot+2QSFP+ TAA Switch JH179A BJNGA-AD0050... -
Page 7: Temperature/Humidity
To ensure correct operation and long service life of your switch, install it in an environment that meets the requirements described in the following subsections. Temperature/humidity Maintain appropriate temperature and humidity in the equipment room. • Lasting high relative humidity can cause poor insulation, electricity creepage, mechanical property change of materials, and metal corrosion. -
Page 8: Laser Safety
(including one pair of mounting brackets and eight M4 • HP 5930-32 QSFP+ countersunk screws) 5066-0850 1 kit • HP 5930-32 QSFP+ TAA Mounting brackets for the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA • HP 5930-2Slot+2QSFP+ 5190-0719 1 kit • HP 5930-2Slot+2QSFP+... - Page 9 Product code Description Quantity Applicable models Mounting brackets for the HP 5930-4Slot/HP 5930-4Slot TAA • HP 5930-4Slot 5190-0720 1 kit • HP 5930-4Slot TAA 1 U short slide rail kit (including • HP 5930-32 QSFP+ one pair of slide rails and four M4 •...
- Page 10 Product code Description Quantity Applicable models Removable cable tie 5185-8748 All power supplies Console cable 5185-8627 All 5930 switches • HP 5930-32 QSFP+ QSFP+ dust plug • HP 5930-32 QSFP+ TAA 5187-9022 Optional • HP 5930-2Slot+2QSFP+ • HP 5930-2Slot+2QSFP+...
-
Page 11: Installing The Switch
Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the chassis, contact HP for permission. Otherwise, HP shall not be liable for any consequence caused thereby. Figure 1 Hardware installation flow... -
Page 12: Installing The Switch In A 19-Inch Rack
2U high, including one pair • HP 5930-4Slot 2U high, one pair. (provided). of chassis rails and one pair • Figure HP 5930-4Slot TAA Figure of slide rails. See Figure Figure 2 Mounting brackets for the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA switch... - Page 13 Figure 3 Mounting brackets for the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch Figure 4 Mounting brackets for the HP 5930-4Slot/HP 5930-4Slot TAA switch (1) Cable management bracket (2) Mounting bracket Figure 5 1U rack mounting rail kit (1) Chassis rail (2) Slide rail...
-
Page 14: Rack-Mounting Procedures At A Glance
• HP 5930-32 QSFP+ Using provided mounting 405 mm (15.94 in) 854 mm (33.62 in) • brackets and chassis rails HP 5930-32 QSFP+ TAA • HP 5930-2Slot+2QSFP+ Using provided mounting • 520 mm (20.47 in) 789 mm (31.06 in) HP 5930-2Slot+2QSFP+... -
Page 15: Attaching The Mounting Brackets, Chassis Rails, And Grounding Cable To The Chassis
(with a grounding sign) and auxiliary grounding point 1. Figure 8 Mounting and grounding positions on the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA switch (1) Auxiliary grounding point 2 (2) Power module-side mounting position... - Page 16 To install the mounting brackets at the power supply-side mounting position on the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA and HP 5930-4Slot/HP 5930-4Slot TAA switches, use the four screw holes nearest to the power supply side.
- Page 17 Figure 10 Attaching the mounting brackets and chassis rails to the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA switch (power supply-side mounting position for the mounting brackets) Figure 11 Attaching the mounting brackets and chassis rails to the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch (power supply-side mounting position for the mounting brackets)
- Page 18 Figure 13 Attaching the mounting brackets and chassis rails to the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA switch (network port-side mounting position for the mounting brackets) Figure 14 Attaching the mounting brackets and chassis rails to the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch (network port-side mounting position for the mounting brackets)
-
Page 19: Attaching The Slide Rails To The Rack
HP recommends that you use the primary grounding point or auxiliary grounding point 1 because the grounding cable and grounding screw that come with the switch are suitable only for these two grounding points. -
Page 20: Mounting The Switch In The Rack
To secure the switch in the rack, make sure the front ends of the slide rails reach out of the chassis rails. The rack-mounting procedures are the same for the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA and HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switches. The following figures use the HP... - Page 21 Figure 18 Mounting the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch in the rack (power supply-side mounting position for the mounting brackets) Figure 19 Mounting the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch in the rack (network port-side mounting position for the mounting brackets)
- Page 22 Figure 20 Mounting the HP 5930-4Slot/HP 5930-4Slot TAA switch in the rack (power supply-side mounting position for the mounting brackets) Figure 21 Mounting the HP 5930-4Slot/HP 5930-4Slot TAA switch in the rack (network port-side mounting position for the mounting brackets)
-
Page 23: Grounding The Switch
NOTE: To rack-mount the HP 5930-4Slot/HP 5930-4Slot TAA switch by using 2U high mounting brackets and slide rails, use two screws and two cage nuts to attach each mounting bracket to the rack. Determine the screw installation positions based on the distances between the square holes on the rack posts. The screw... -
Page 24: Grounding The Switch By Using The Ac Power Cord
(3) Grounding post (4) Grounding strip HP recommends that you use the primary grounding point or auxiliary grounding point 1 on the switch, because the grounding cable and grounding screw provided with the switch are applicable only to these two grounding points. -
Page 25: Installing/Removing A Fan Tray
• When two fan trays fail during switch operation: Finish replacing the fan trays within 2 minutes on an HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA or HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch. Finish replacing the fan trays within 1 minute on an HP 5930-4Slot/HP 5930-4Slot TAA switch. -
Page 26: Installing A Fan Tray
Installing a fan tray CAUTION: To prevent damage to the fan tray or the connectors on the backplane, insert the fan tray gently. If you encounter a hard resistance while inserting the fan tray, pull out the fan tray and insert it again. Select appropriate fan trays as needed. -
Page 27: Removing A Fan Tray
Figure 25 Installing an LSWM1BFANSC/LSWM1BFANSCB fan tray Removing a fan tray WARNING! Ensure electricity safety and never touch the rotating fans when you hot-swap a fan tray. • To prevent an unbalanced fan from causing loud noise, do not touch the fans, even if they are not •... -
Page 28: Installing/Removing A Power Supply
Figure 26 Removing an LSWM1BFANSC/LSWM1BFANSCB fan tray Installing/removing a power supply WARNING! In power redundancy mode, you can replace a power supply without powering off the switch but must • strictly follow the installation and procedures in Figure 27 Figure 28 to avoid any bodily injury or damage to the switch. -
Page 29: Installing A Power Supply
Install filler panels in the empty power supply slots for good ventilation of the switch. • The power supply installation procedures are the same for the HP FlexFabric 5930 switches. This section uses the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA switch as an example. -
Page 30: Removing A Power Supply
The power supply removing procedures are the same for the HP FlexFabric 5930 switches. This section uses the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA switch as an example: To remove a power supply: Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded. -
Page 31: Connecting The Power Cord
Figure 31 Removing the DC power cord (1) Press the tabs on the power cord connector with your thumb and (2) Pull the power cord connector out forefinger Figure 32 Removing the power supply (1) Pivot the latch to the right with your thumb (2) Pull the power supply out Connecting the power cord WARNING! -
Page 32: Connecting The 650W Ac Power Supply
Connecting the 650W AC power supply Insert the female connector of the AC power cord supplied with the power supply into the power receptacle on the power supply. Use a cable tie to secure the power cord to the handle of the power supply, as shown in Figure Connect the other end of the power cord to an AC power outlet. -
Page 33: Installing/Removing An Interface Module
• Do not use excessive force. The HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch provides two interface module slots. The HP 5930-4Slot/HP 5930-4Slot TAA switch provides four interface module slots. For the available interface modules, see "Appendix B FRUs and compatibility matrixes."... - Page 34 Figure 36 LSWM18QC interface module (1) Ejector lever (2) Latch Press the latch on the interface module to release the ejector lever. Insert the interface module slowly into the slot along the guide rails, as shown by callout 1 in Figure Rotate inward the ejector lever as shown by callout 2 in Figure 37...
-
Page 35: Verifying The Installation
Figure 38 Removing an LSWM18QC interface module Verifying the installation After you complete the installation, verify that: There is enough space for heat dissipation around the switch, and the rack is stable. • The grounding cable is securely connected. • •... -
Page 36: Accessing The Switch For The First Time
Accessing the switch for the first time Setting up the configuration environment The switch supports the following ways to connect the configuration terminal: Through the console port by using the serial console cable • The switch comes with the serial console cable. This way is preferred. Through the USB mini console port by using the user-supplied USB mini console cable •... -
Page 37: Usb Mini Console Cable
Figure 40 Serial console cable A side Pos.9 Main label B side Pos.1 Table 7 Serial console cable pinout RJ-45 Signal DB-9 Signal USB mini console cable A USB mini console cable has a USB mini-Type B connector at one end to connect to the USB mini console port of the switch, and a standard USB Type A connector at the other end to connect to the USB port on the configuration terminal. - Page 38 Connect the USB mini Type B connector to the USB mini console port of the switch. Click the following link, or copy it to the address bar on the browser to log in to download page of the USB console driver, and download the driver. http://www.exar.com/connectivity/uart-and-bridging-solutions/usb-uarts/xr21v1410 Select a driver program according to the operating system you use: XR21V1410_XR21B141 1_Windows_Ver1840_x86_Installer.EXE—32-bit operating system.
-
Page 39: Setting Terminal Parameters
Figure 42 Software Installation Click Finish. Figure 43 Completing the device driver installation wizard Setting terminal parameters To configure and manage the switch through the console port, you must run a terminal emulator program, HyperTerminal or PuTTY, on your configuration terminal. You can use the emulator program to connect a... -
Page 40: Powering On The Switch
After the startup completes, you can access the CLI to configure the switch. For more information about the configuration commands and CLI, see HP FlexFabric 5930 Switch Series Configuration Guide and HP FlexFabric 5930 Switch Series Command References. -
Page 41: Setting Up An Irf Fabric
Setting up an IRF fabric You can use HP IRF technology to connect and virtualize HP FlexFabric 5930 switches into a large virtual switch called an "IRF fabric" for flattened network topology, and high availability, scalability, and manageability. To set up IRF links between two switches, use the 10-GE or 40-GE ports. -
Page 42: Planning Irf Fabric Setup
Distribute the IRF member switches in different racks to implement the top-of-rack (ToR) access solution for a data center. As your business grows, you can plug HP FlexFabric 5930 switches into the IRF fabric to increase the switching capacity without any topology change or replacement. -
Page 43: Planning Irf Topology And Connections
NOTE: IRF member switches will automatically elect a master. You can affect the election result by assigning a high member priority to the intended master switch. For more information about master election, see FlexFabric 5930 Switch Series IRF Configuration Guide Prepare an IRF member ID assignment scheme. -
Page 44: Identifying Physical Irf Ports On The Member Switches
Identify the 1/10-GE Ethernet ports, SFP+ ports, and QSFP+ ports to be used for IRF connections on the member switches according to your topology and connection scheme. All the 1/10-GE Ethernet ports, SFP+ ports, and QSFP+ ports on the HP FlexFabric 5930 switch can be used for IRF connections. -
Page 45: Configuring Basic Irf Settings
Configuring basic IRF settings After you install the IRF member switches, power on the switches, and log in to each IRF member switch (see HP FlexFabric 5930 Switch Series Fundamentals Configuration Guide) to configure their member IDs, member priorities, and IRF port bindings. -
Page 46: Connecting The Physical Irf Ports
Create a Layer 3 interface, assign it an IP address, and make sure the IRF fabric and the remote network management station can reach each other. Use Telnet, Web, or SNMP to access the IRF fabric from the network management station. (See HP FlexFabric 5930 Switch Series Fundamentals Configuration Guide.) Verify that you can manage all member switches as if they were one node. -
Page 47: Maintenance And Troubleshooting
Power supply failure You can use the LEDs on the power supply to identify a power supply failure. For more information about the LEDs on a power supply, see HP A58x0AF 650W AC (JC680A) & 650W DC (JC681A) Power Supplies User Guide. -
Page 48: Configuration Terminal Problems
Baud rate—9600. Data bits—8. Stop bits—1. Parity—None. Flow control—None. If the problem persists, contact HP Support. Garbled terminal display The configuration terminal displays garbled text. To resolve the problem: Verify that the following settings are configured for the terminal: Baud rate—9600. -
Page 49: Appendix A Chassis Views And Technical Specifications
"Installing/removing a power supply." The HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA switch comes with the two fan tray slots empty. You must install two fan trays of the same model for the switch. In Figure 51, two LSWM1HFANSC fan trays are installed in the fan tray slots. -
Page 50: Hp 5930-2Slot+2Qsfp+/Hp 5930-2Slot+2Qsfp+ Taa
(11) Management Ethernet port (12) Serial console port The HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch comes with interface module slot 1 empty and interface module 2 installed with a filler panel. You can install one or two interface modules for the switch as needed. In... -
Page 51: Hp 5930-4Slot/Hp 5930-4Slot Taa
The HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch comes with the two fan tray slots empty. You must install two fan trays of the same model for the switch. In Figure 54, two LSWM1HFANSC fan trays are installed in the fan tray slots. For more information about installing and removing fan trays, "Installing/removing a fan... -
Page 52: Technical Specifications
"Installing/removing a power supply." The HP 5930-4Slot/HP 5930-4Slot TAA switch comes with the two fan tray slots empty. You must install two fan trays of the same model for the switch. In Figure 57, two LSWM1HFANSC fan trays are installed in the fan tray slots. - Page 53 HP 5930-32 QSFP+/HP HP 5930-4Slot/HP Item 5930-2Slot+2QSFP+/HP 5930-32 QSFP+ TAA 5930-4Slot TAA 5930-2Slot+2QSFP+ TAA Fan tray slots Power supply slots • Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz AC-input voltage • Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz •...
-
Page 54: Appendix B Frus And Compatibility Matrixes
5930-2Slot+2QSFP+ TAA switches can operate correctly with only one power supply. You can install two power supplies on the switches for 1+1 redundancy. The HP 5930-4Slot/HP 5930-4Slot TAA switch can operate correctly with two power supplies. You can • install four power supplies on the switches for 2+2 redundancy. -
Page 55: Fan Trays
Fan trays Table 12 Fan tray specifications Item Specifications LSWM1HFANSC (for the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA and HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switches) Fans Two 40 × 40 × 56 mm (1.57 × 1.57 × 2.2 in) fans Fan speed 21000 R.P.M... -
Page 56: Interface Modules
Interface modules The HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switch provides two interface module slots. The HP 5930-4Slot/HP 5930-4Slot TAA switch provides four interface module slots. Select interface modules for the switch as required. Table 13 Interface modules available for the HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA... - Page 57 Interface Product Transceiver modules available HP description Alias number and code for the ports type NOTE: HP 5930 24-port SFP+ and 2-port Only the SFP+ ports on the JH181A LSWM124XG2Q QSFP+ with MacSec LSWM124XG2QFC interface Module module support the •...
-
Page 58: Appendix C Ports And Leds
Appendix C Ports and LEDs Ports Console port The switch has two console ports: serial console port and Mini USB console port. Table 14 Console port specifications Item Console port Mini USB console port Connector type RJ-45 USB mini-Type B Compliant EIA/TIA-232 USB 2.0... -
Page 59: Usb Port
NOTE: USB devices from different manufacturers vary in compatibilities and drivers. HP does not guarantee the correct operation of all USB devices on the switch. If a USB device fails to operate on the switch, replace it with one from another manufacturer. - Page 60 Table 18 SFP+ DAC cables available for the SFP+ ports Product HP description Max transmission distance Data rate code JD095B HP X240 10G SFP+ SFP+ 0.65m DA Cable 0.65 m (2.13 ft) 10.31 Gbps JD096B HP X240 10G SFP+ SFP+ 1.2m DA Cable 1.2 m (3.94 ft) 10.31 Gbps...
-
Page 61: Qsfp+ Port
HP recommends that you use HP SFP transceiver modules, SFP+ transceiver modules, or SFP+ DAC cables for the SFP+ ports on the switch. The HP SFP transceiver modules, SFP+ transceiver modules, and SFP+ DAC cables are subject to change over time. For the most up-to-date list of SFP transceiver modules, SFP+ transceiver modules, and SFP+ DAC cables, contact HP Support or marketing staff. - Page 62 HP description Cable length Code JG329A HP X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable 1 m (3.28 ft) JG330A HP X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable 3 m (9.84 ft)
-
Page 63: 1/10Gbase-T Autosensing Ethernet Port
HP recommends that you use HP QSFP+ transceiver modules, QSFP+ DAC cables, or QSFP+ to SFP+ • DAC cables for the QSFP+ ports on the switch. The HP QSFP+ transceiver modules, QSFP+ DAC cables, and QSFP+ to SFP+ DAC cables available for the interface modules are subject to change over time. For the most recent list of QSFP+ transceiver modules, QSFP+ DAC cables, and QSFP+ to SFP+ DAC cables available for the interface modules, contact HP Support or marketing staff. -
Page 64: Leds
Separate power cords and twisted pair cables at and around the distribution frame. • For ports adjacent to one another on the device, the peer ports on the distribution frame are • preferably not adjacent, for example: If the device connects to one distribution frame, connect port 1 on the device to port 1 on the distribution frame, port 2 on the device to port 3 on the distribution frame, and port 3 on the device to port 5 on the distribution frame. -
Page 65: Management Ethernet Port Leds
The HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA and HP 5930-4Slot/HP 5930-4Slot TAA switches provide a LINK LED and an ACT LED for the management Ethernet port. Table 26 Management Ethernet port LED description for the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA and HP 5930-4Slot/HP 5930-4Slot TAA switches... -
Page 66: Fan Tray Alarm Leds
Status Description Steady yellow The port has a link and is operating at 1 Gbps. Flashing yellow The port is sending or receiving data at 1 Gbps. No link is present on the port. Fan tray alarm LEDs The LSWM1BFANSC and LSWM1BFANSCB fan trays provide an Alarm LED. Table 29 LSWM1BFANSC and LSWM1BFANSCB fan tray alarm LED description Status Description... -
Page 67: Appendix D Cooling System
HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA and HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA cooling system You must install two fan trays of the same model for the HP 5930-32 QSFP+/HP 5930-32 QSFP+ TAA and HP 5930-2Slot+2QSFP+/HP 5930-2Slot+2QSFP+ TAA switches: LSWM1HFANSC or LSWM1HFANSCB. -
Page 68: Hp 5930-4Slot/Hp 5930-4Slot Taa Cooling System
The chassis and the power supplies use separate air aisles. Make sure both aisles are not blocked. HP 5930-4Slot/HP 5930-4Slot TAA cooling system You must install two fan trays of the same model for the HP 5930-4Slot/HP 5930-4Slot TAA switch: LSWM1BFANSC or LSWM1BFANSCB. - Page 69 Figure 65 Airflow through the HP 5930-4Slot/HP 5930-4Slot TAA chassis (with the LSWM1BFANSCB fan trays) IMPORTANT: The chassis and the power supplies use separate air aisles. Make sure both aisles are not blocked.
-
Page 70: Support And Other Resources
Related information Documents To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals • For related documentation, navigate to the Networking section, and select a networking category. -
Page 71: Conventions
Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax choices separated by vertical bars, from which { x | y | ... - Page 72 Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.
-
Page 73: Index
Index A C E F G H I L P S T V Installation tools,4 Installing the switch in a 19-inch rack,8 Accessing the IRF fabric to verify the configuration,42 Installing/removing a fan tray,21 Installing/removing a power supply,24 IRF fabric setup flowchart,37 Chassis views,45...