Mode Button Setting; Obtaining The Autonomous Access Point Image File - Cisco Aironet 1130AG Series Hardware Installation Manual

Cisco Aironet 1130AG Series Access Point Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
4-10 4-10
Chapter 4 4 Chapter Troubleshooting Troubleshoo

MODE Button Setting

MODE Button Setting

Obtaining the Autonomous Access Point Image File

Obtaining the Autonomous Access Point Image File
Note Note
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
St Step ep 5 5
St Step ep 6 6
St Step ep 7 7
St Step ep 8 8
St Step ep 9 9
St Step ep 10 10
St Step ep 11 11
St Step ep 12 12
St Step ep 13 13
St Step ep 14 14
St Step ep 15 15
St Step ep 16 16
St Step ep 17 17
Hardware Installation Guide
ting Lightweig Lightweight ht Access Access Points Points
The lightweight access point MODE button is configured from your Cisco Wireless LAN Controlle The lightweight access point MODE button is configured from your Cisco Wireless LAN Controlle r. Use
these controller CLI commands to view and configure the MODE button: these controller CLI commands to view and configure the MODE button:
1) 1)
config ap rst-button enable <access-point-name>/all config ap rst-button enable <access-point-name>/all
2) 2)
config ap rst-button disable <access-point-name>/all config ap rst-button disable <access-point-name>/all
3) 3) show ap config general <access-point-name> show ap config general <access-point-name>
(Where access-point-name (Where access-point-name
ocntroller.) ocntroller.)
The autonomous access point imag The autonomous access point imag e file can be obtained from the Cisco.com software center using the
steps: steps:
To download software from the Cisco.com software center, you must be a registered user. You can To download software from the Cisco.com software center, you must be a registered user. You can
register from the main Cisco.com web page at this URL: register from the main Cisco.com web page at this URL: http://cisco.com
Use your Internet browser to access the Cisco Software Center at the following URL: Use your Internet browser to access the Cisco Software Center at the following URL:
http://tools.cisco.com/support/downloads/pub/MDFTree.x?butype=wireless http://tools.cisco.com/support/downloads/pub/MDFTree.x?butype=wireless
Click Click Wireless LAN Access > Aironet Access Points Wireless LAN Access > Aironet Access Points > Cisco Aironet 1130
Click Click Cisco Aironet 1130AG Access Point Cisco Aironet 1130AG Access Point. .
On the Enter Network Password window, enter your Cisco.com username and password and click On the Enter Network Password window, enter your Cisco.com username and password and click OK
Click Click IOS IOS. .
Choose the Cisco IOS release desired, such as 12.3.8.JA. Choose the Cisco IOS release desired, such as 12.3.8.JA.
Click Click WIRELESS LAN WIRELESS LAN for an access point image file, such as c1130-k9w7-tar.123-8.JA.ta for an access point image file, such as c1130-k9w7-tar.123-8.JA.ta r r . .
On the Enter Network Password window, enter your Cisco.com username and password and click OK On the Enter Network Password window, enter your Cisco.com username and password and click
On the Security Information window, click Y Y es es to display non-secure items. On the Security Information window, click
On the Encryption Software Export Authorization page, rea On the Encryption Software Export Authorization page, rea d the information and check
question asking if the image is for use by you or your organization. Click question asking if the image is for use by you or your organization. Click Submit
If you checked No, enter the requested information and click If you checked No, enter the requested information and click Submit
Click Click Yes Yes to continue. to continue.
Click DOWNLOAD Click DOWNLOAD. .
Read and accept the terms and conditions of the Software Download Rules. Read and accept the terms and conditions of the Software Download Rules.
On the Enter Network Password window, enter your Cisco.com username and password and click OK On the Enter Network Password window, enter your Cisco.com username and password and click
Click Save Click Save to download your image file to your hard disk. to download your image file to your hard disk.
Select the desired download location on your hard disk and click Save Select the desired download location on your hard disk and click
Obtaining the Autonomous Access Point Image File Obtaining the Autonomous Access Point Image File
is the name that identifies the access point on the is the name that identifies the access point on the
e file can be obtained from the Cisco.com software center using the se se
http://cisco.com. .
> Cisco Aironet 1130 AG Series
to display non-secure items.
d the information and check Y Y es es or
OL-8369-04 OL-8369-04
AG Series. .
Submit.. ..
Submit. .
Save. .
r. Use
OK. .
OK. .
or No No to the to the
OK. .