Reloading The Access Point Image; Using The Mode Button; Web Browser Interface - Cisco Aironet 1130AG Series Hardware Installation Manual

Cisco Aironet 1130AG Series Access Point Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
3-16 3-16
Chapter 3 3 Chapter Troubleshoo Troubleshooting
St Step ep 7 7
St Step ep 8 8

Reloading the Access Point Image

Reloading the Access Point Image

Using the MODE Button

Using the MODE Button
Note Note
Note Note
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
St Step ep 5 5
St Step ep 6 6
St Step ep 7 7
St Step ep 8 8
Hardware Installation Guide
ting Autonomous Autonomous Access Access Points Points
Click Click Reset to Reset to Defaults Defaults. .
Note Note If the access point is configured with a static IP address, the IP address does not change. If the access point is configured with a static IP address, the IP address does not change.
After the access point reboots, you must reconfigure the acces s point by using the W After the access point reboots, you must reconfigure the acces
the Telnet interface, or Cisco IOS commands. the Telnet interface, or Cisco IOS commands.
If your access point has a firmware failure, you must reload the complete access point image file using If your access point has a firmware failure, you must reload the complete access point image file using
the Web browser interface or by using the MODE button. the Web browser interface or by using the MODE button. Y Y ou can use the b
point firmware is still fully operational and y point firmware is still fully operational and y ou want to upgrade the firmware image. However, you can
use the MODE button when the access point has a corrupt firmware image. use the MODE button when the access point has a corrupt firmware image.
You can use the MODE button on the access point to reload the access point image file from an active You can use the MODE button on the access point to reload the access point image file from an active
Trivial File Transfer Protocol (TFTP) server on your network or on a PC connected to the access point Trivial File Transfer Protocol (TFTP) server on your network or on a PC connected to the access point
Ethernet port. Ethernet port.
If your access point experiences a firmware failure or a corrupt firmware image, indicated by the Status If your access point experiences a firmware failure or a
LED turning an amber color, you must reload the image from a connected TFTP server. LED turning an amber color, you must reload the image from a connected TFTP server.
This process resets This process resets all all configuration settings to factory defaults, including passwords, WEP keys, the configuration settings to factory defaults, including passwords, WEP keys, the
access point IP address, and SSIDs. access point IP address, and SSIDs.
Follow these steps to reload the access point image file: Follow these steps to reload the access point image file:
The PC you intend to use must be configured with a static IP address in the same subnet as the access The PC you intend to use must be configured with a static IP address in the same subnet as the access
point. point.
Place a c opy of the Place a c opy of the access point i access point i mage file (such
folder on your PC. For additional information, refer to the "Obtaining the Access Point Image File" folder on your PC. For additional information, refer to the
"Obtaining the TFTP Server "Obtaining the TFTP Server Software"
Rename the access point image file in the TFTP server folder to c1130-k9w7-tar.default Rename the access point image file in the TFTP server folder to
Activate the TFTP server. Activate the TFTP server.
If using in-line power, use a Category 5 (CAT5) Ethernet cable to connect your PC to the To Network If using in-line power, use a Category 5 (CAT5) Ethernet cable to connect your PC to the
Ethernet connector on the power injector. Ethernet connector on the power injector.
Open the access point cover (refer to the "Opening the Acce Open the access point cover (refer to the
Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the
access point. access point.
Press and hold the MODE MODE button while you reconnect power to the access point.
Press and hold the button while you reconnect power to the access point.
ou want to upgrade the firmware image. However, you can
corrupt firmware image, indicated by the Status
mage file (such as c1130-k as c1130-k9w7-ta
Software" sections. sections.
"Opening the Access Point Cov
Reloading the Access Point Image Reloading the Access Point Image
s point by using the Web browser interface, eb browser interface,
ou can use the b rowser interface if the access rowser interface if the access
9w7-tar r .123- .123-8.J 8.JA.tar A.tar) into the ) into the TFTP server
"Obtaining the Access Point Image
c1130-k9w7-tar.default . .
ss Point Cover" sectio er" section on page n on page
OL-8369-04 OL-8369-04
TFTP server
File" and and
To Network
2-11). ). 2-11