Cisco Aironet 1130AG Series Hardware Installation Manual page 69

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access Point
3-12 3-12
Chapter 3 3 Chapter Troubleshoo Troubleshooting
T T ab able le 3- 3-3 3
P P o o w w e e r r S S o o u u r r c c e e
2 2
Power injector Power injector
Cisco switch that supports Cisco switch that supports
Intelligent Power Management Intelligent Power Management
2 2
Power injector Power injector
Cisco switch that does not Cisco switch that does not
support Intelligent Power support Intelligent Power
1 1
Management Management
Power injector used with a Power injector used with a
non-Cisco switch non-Cisco switch
802.3af compliant non-Cisco 802.3af compliant non-Cisco
switches switches
1. 1. You should check the releas You should check the release notes for your Cisco power source to de
for Intelligent Power Management might not be currently available for for Intelligent Power Management might not be currently available for your Cisco power source.
2. 2. Powe Power inject r injector must be AIR or must be AIR-PWR
3. 3. Cisco switch Cisco switches that support I es that support Intelligent Po
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
Hardware Installation Guide
ting Autonomous Autonomous Access Access Points Points
Acce Ac cess ss P P oi oint nt S S ys yste tem m Po Powe wer S
A A c c c c e e s s s s P P o o i i n n t t S S y y s s t t e e m m P P o o w w e e r r S S e e t t t t i i n n g g s s
used with a used with a Power Settings: Power Settings:
Power Negotiation (selected) Power Negotiation
1 1
Power Injector: Power Injector:
Installed on Port with MAC Address Installed on
used with a used with a Power Settings: Power Settings:
Power Negotiation Power Negotiation (selected)
Power Injector: Power Injector:
Installed on Installed on Port with MAC Address
C C o o n n f f i i g g u u r r a a t t i i o o n n c c h h a a n n g g e e s s a a r r e e n n o o t t r r e e q q u u i i r r e e d d
C C o o n n f f i i g g u u r r a a t t i i o o n n c c h h a a n n g g e e s s a a r r e e n n o o t t r r e e q q u u i i r r e e d d
e notes for your Cisco power source to determine which Cisco IOS rele
-PWRINJ3 or AIR INJ3 or AIR-PWR -PWRINJ-
ntelligent Power Management a wer Management always configure th
Follow these steps to configure your access point power settings using the browser interface: Follow these steps to configure your access point power settings using the browser interface:
Obtain the access point IP address and browse to your access point. Obtain the access point IP address and browse to your access point.
Choose one of these operations: Choose one of these operations:
a. a. When you browse to your access point operating in low-power mode, a Warning message appears When you browse to your access point operating in low-power mode, a Warning message appears
indicating that all radios are disabled due to insufficient power. Click OK indicating that all radios are disabled due to insufficient power. Click
Power Settings located on the System Software > System Configuration page. Power Settings located on the System Software > System Configuration page.
b. b. When you browse to your access point operating in full-power mode, choose
When you browse to your access point operating in full-power mode, choose System Software >
System Configuration. . System Configuration
Choose one of these Power Settings options (see Fi Figur Choose one of these Power Settings options (see
a. a. If your Cisco switch supports Intelligent Power Management negotiations, choose If your Cisco switch supports Intelligent Power Management negotiations, choose Power
Negotiation. . Negotiation
b. b. If your Cisco switch does not support Intelligent Power Management negotiations, choose If your Cisco switch does not support Intelligent Power Management negotiations, choose
Pre-standard Compatibility Pre-standard Compatibility. .
c. c. If you are using a non-Cisco switch, changes to the power settings are not required. If you are using a non-Cisco switch, changes to the power settings are not required.
r Set etti ting ngs a s and nd Ci Cisc sco S o Swi witc tch C h Com
(selected)
Port with MAC Address (unchecked)
(selected)
Port with MAC Address (checked)
termine which Cisco IOS release supports Intell
your Cisco power source.
INJ-FIB. FIB.
lways configure the use of a power e use of a power injector at the
Low Power Condition for Autonomous Access Points Low Power Condition for Autonomous Access Points
omma mand nds ( s (co cont ntin inue ued) d)
(unchecked)
(checked)
ase supports Intelligent Power Management igent Power Management. Support
injector at the switch. switch.
OK to jump to the System to jump to the System
gure e 3- 3-2 2 ): ):
OL-8369-04 OL-8369-04
Cisco Switch Cisco Switch
Power Command Power Command
3 3
power inline never power inline never
power inline never power inline never
– –
– –
. Support
System Software >
Power