Page 1
MODWAY HEADBOARD Thank you for purchasing the MOD-5365/5366/5367/5368/5369/5370/5371/5372/5373/5374/5375/5376/5377/ 5378/5379/5380/5381/5382/5383/5384/5385/5386/5387/5388/5389/5390/5391/5392/5393/5394/5395/5396/5397/ 5398/5399/5400/5401/5402/5403/5404/5405/5406/5407/5408 HEADBOARD! ! ! ! Before you start, here is some helpful advice: 1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions.
Page 2
MODWAY HEADBOARD STEP 1: Put the Headboard (1) upside down on a carpeted or padded area by two adults Then insert the Low Posts (2) into the bottom of Headboard (1) and align pre-drilled Low Post (2) holes to the pre- drilled Headboard (1) Holes according to your desired headboard height.
Page 3
MODWAY CONNECTING HEADBOARD TO BED FRAME ASSEMBLY INSTRUCTIONS OPTION 1 Hardware: OPTION 1 Bolt M6x45mm Bolt M6x65mm Flat Washer M6xD22mm Spring Washer M6 Hex Nut M6 Allen Wrench M4 Component: OPTION 1 Bed Frame Headboard (Style may vary) Customer Service 908-368-1025︱ ︱ ︱ ︱ www.modwayfurniture.com...
Page 4
MODWAY CONNECTING HEADBOARD TO BED FRAME Note: Extra hardware were provided for attaching the headboard to your Bed Frame (use is optional). STEP 1: Line up the Bed Frame (2) board’s pre-drilled holes to match those of the Headboard (1) .
Page 5
MODWAY CONNECTING HEADBOARD TO BED FRAME ASSEMBLY INSTRUCTIONS OPTION 2 Note: This is assembly instruction for Headboard connect to MODWAY Bed Frame MOD-5347/5348/5349/ 5350/5351/5352/5353/5354/5357/5358/5359/5360/5361/5362/5363/5364. Hardware: OPTION 2 Bolt M6x45mm Bolt M6x65mm Flat Washer M6xD22mm Spring Washer M6 Allen Wrench M4...
Page 6
MODWAY CONNECTING HEADBOARD TO BED FRAME STEP 1: Line up the Bed Fame (2) board’s pre-drilled holes to match those of the Headboard (1). Secure the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolt (B) with 2 pieces of Spring Washer (D), 2 pieces of Flat Washer (C) for the thicker Bed Frame (2), and 2 pieces of Bolt (A) with 2 pieces of Spring Washer (D), 2 pieces of Flat Washer (C) for the thinner Bed Frame (2).
Page 7
MOD-5359/5360/5361/5362 FULL/QUEEN BED FRAME Components: Short Board Long Board Center Rail Support Leg x4 Leg I Leg II Roll Slats WWW.MODWAY.COM...
Page 8
Attach them by using 4 pieces of Bolt (A) as shown. Use Allen Wrench (G) to tighten the Bolts (A) clockwise until secure. Repeat the same steps for the remaining 1 piece of Long Board (1). A x 8 G x 1 WWW.MODWAY.COM...
Page 9
Support leg (4) clockwise until secure. Insert Center Rail (3) to the bracket (provided) on Short Board (1) and then secure with 1 piece Screw (E) per each side end. Tighten the Screws (E) with Phillips Head Screw Driver (not provided). E x 2 WWW.MODWAY.COM...
Page 10
E x 8 E x 4 Assembly is complete. The bed frame is ready to use now! Hardware may loosen over time. Periodically check that all connections are tight. WWW.MODWAY.COM...
Page 11
CONNECTING BED FRAME TO HEADBOARD Reminder: All the hardware packed in the Headboard you bought. Please use only the above hardware from Headboard Hardware Package to assemble the Bed Frame and Headboard. WWW.MODWAY.COM...
Page 12
CONNECTING BED FRAME TO HEADBOARD WWW.MODWAY.COM...
Need help?
Do you have a question about the MOD-5365 and is the answer not in the manual?
Questions and answers