Ryobi ONE+ CLT1830P User Manual page 22

GB GB
F F D D E E
REWINDING THE EXISTING SPOOL
See Figure 14.
Remove the battery pack from the string trimmer.
■
Press in the tabs on each side of the spool cap.
■
Remove the spool cap and spool. Discard any
■
remaining line on the spool.
NOTE: If the spring falls off the spool housing during
this procedure, reinstall the spring before installing
the spool and spool cap.
Inspect the string head for damaged or worn parts
■
and clean thoroughly.
Using approximately 3 m (10 feet) of new cutting line,
■
insert one end of the line into the slot on the spool.
Ensure the end of the line is pushed all the way
towards the inner side of slot.
NOTE: No more than 3.175 mm (1/8 in.) of the line is
to protrude from the slot.
Wind the line, in even and tight layers, onto the spool.
■
Line should be wound in the direction of the arrow
indicated on the spool.
Unwind approximately 102 mm (4 in.) of the line from
■
the spool. Hold the line and spool firmly to keep it from
unwinding then place the spool cap onto the spool.
Holding the spool cap and spool by the bump knob,
■
place into the spool housing and insert cutting line
into the opening in spool housing.
NOTE: Tabs on the spool cap should be aligned with
the slots in the spool housing.
While pressing in the tabs, push down the spool cap
■
and spool to lock in place.
Completely assembled string head should appear as
■
shown. See Figure 15.
WARNING
Use only 1.65 mm (0.065 in) diameter genuine
replacement line. Never use metal reinforced
line, wire, or rope, etc. These can break off and
become a dangerous projectile. Do not use any
other attachment on this unit.
INSTALLING A PREWOUND SPOOL
See Figure 14.
Remove the battery pack from the string trimmer.
■
Press in the tabs on each side of the spool cap.
■
Remove the spool cap and spool.
■
NOTE: If the spring falls off the spool housing during
this procedure, reinstall the spring before installing
the spool and spool cap.
Inspect the string head for damaged or worn parts
■
and clean thoroughly.
Unwind approximately 102 mm (4 in.) of the line from
■
the prewound spool. Hold the line and spool firmly to
keep it from unwinding then place the spool cap onto
the spool.
Holding the spool cap and spool by the bump knob,
■
place into the spool housing and insert cutting line
into the opening in spool housing.
NOTE: Tabs on the spool cap should be aligned with
I I P P NL NL S S DK DK N N FIN GR HU FIN GR HU CZ RU CZ RU
English
the slots in the spool housing.
While pressing in the tabs, push down the spool cap
■
and spool to lock in place.
Completely assembled string head should appear as
■
shown. See Figure 15.
CLEANING THE STRING TRIMMER
Remove the battery pack.
■
Clean the unit using a damp cloth with a mild
■
detergent.
Do not use any strong detergents on the plastic
■
housing or the handle. They can be damaged by
certain aromatic oils such as pine and lemon, and by
solvents such as kerosene.
Moisture can cause a shock hazard. Wipe off any
■
moisture with a soft dry cloth. Use a small brush or
the air discharge of a small vacuum cleaner brush to
clean the air vents on the battery pack housing and
motor housing.
Keep the air vents free of obstructions.
■
STORING THE STRING TRIMMER
Clean the string trimmer thoroughly before storing.
■
Store the string trimmer in a dry, well ventilated place
that is inaccessible to children. Keep away from
corrosive agents such as garden chemicals and
de-icing salts.
Store and charge your batteries in a cool area.
■
Temperatures above or below normal room
temperature will shorten battery pack life.
Never store batteries in a discharged condition.
■
Wait for battery pack to cool and charge immediately.
All batteries gradually lose their charge. The higher
■
the temperature, the quicker they lose their charge.
If you store your unit for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery pack live.
16
RO PL SLO HR TR EST LT RO PL SLO HR TR EST LT
WARNING
Do not attempt to modify this unit or create or
mount any accessory
recommended in this manual for use with
this string trimmer. Any such alteration or
modification is misuse and could result in a
hazardous condition leading to possible serious
personal injury. Examine string trimmer
frequently to assure all parts are unbroken and
securely attached. Make sure all screws and
fasteners are securely tightened to prevent the
risk of serious personal injury.
WARNING
To prevent serious personal injury, remove the
battery pack before servicing, cleaning,
or removing material from the unit.
LV LV SK BG SK BG
not specifically