Ryobi ONE+ CLT1830P User Manual page 20

GB GB
F F D D E E
ADJUSTING THE SHAFT
Rotate the lower portion of the shaft adjustment collar
■
to the "Unlock" position. See Figure 4.
Lower shaft should now be free to slide down from
■
inside the upper shaft. Make sure the shaft is pulled
out to the desired position. See Figure 5.
Rotate shaft adjustment collar to the "Lock" position
■
and tighten securely. See Figure 6.
WARNING
If any parts are missing, do not operate unit until
the missing parts are replaced. Failure to do so
could result in possible serious personal injury.
OPERATION
LED FUNCTIONS OF CHARGER
See Figure 16.
LED WILL BE ON TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
Red LED on = Fast charging mode.
■
Green LED on = Fully charged battery pack.
■
No LED on = Defective charger or battery pack.
■
CAUTION
To prevent damage to battery pack, remove
battery pack from charger immediately if no LED
comes on. Return battery pack and charger to
your nearest Authorised Service Centre for
checking or replacing. Also, if you are removing
battery pack from charger and no LEDs are on,
return both battery pack and charger to your
nearest Authorised Service Centre. Do not insert
another battery pack into charger. A damaged
charger may damage a battery pack.
CHARGING YOUR BATTERY PACK
The battery pack for this unit has been shipped in a low
charge condition to prevent possible problems.
Therefore, you should charge it prior to use.
NOTE: Batteries will not reach full charge the first time
they are charged. Allow several cycles (trimming followed
by recharging) for them to fully charge.
TO CHARGE
Charge battery pack only with the charger provided.
■
Make sure power supply is normal household
■
voltage, 230 volts, 50 Hz, AC only.
Connect charger to power supply.
■
Place battery pack in charger. Align raised rib on
■
battery pack with groove in charger.
When charger is properly connected, red light will
■
turn on. Press down on battery pack to be sure
contacts on battery pack engage properly with
contacts in charger.
I I P P NL NL S S DK DK N N FIN GR HU FIN GR HU CZ RU CZ RU
English
Normally, the yellow and green lights on the charger
■
will come on. This indicates charger is in control
charge mode and should switch to fast charge mode
within 5 minutes. When charger is in fast charge
mode the yellow and green lights will go off and the
red light will come on.
If after a period of 15 minutes the yellow and green
lights remain on, remove the battery pack, wait
1 minute and reinsert battery pack in charger. If the
yellow and green lights continue to remain on an
additional 15 minutes, the battery pack is damaged
and will not accept charge.
When your battery pack becomes fully charged,
■
the red light will turn off and the green light will
turn on. After normal usage, 1 hour of charge time is
required to be fully charged. A minimum charge time
of 1 to 1-1/ 2 hours is required to recharge a
completely discharged battery pack. The battery pack
will become slightly warm to the touch while charging.
This is normal and does not indicate a problem.
DO NOT place charger in an area of extreme heat
■
or cold. It will work best at normal room temperature.
IMPORTANT INFORMATION FOR RECHARGING HOT
BATTERY PACK
When using your line trimmer continuously,
the batteries in your battery pack will become hot.
You should let a hot battery pack cool down for
approximately 30 minutes before attempting to recharge.
NOTE: This situation only occurs when continuous use of
your line trimmer causes the batteries to become hot.
It does not occur under normal circumstances. If battery
pack is below normal temperature range, the green LED
on charger will come on. Allow battery pack to reach
normal temperature, then the red LED will come on.
INSTALL BATTERY PACK
Place the battery pack in the string trimmer.
■
Align raised rib on battery pack with groove in string
trimmer. See Figure 7.
Make sure the latches on the battery pack snap in
■
place and that battery pack is secured in string
trimmer before beginning operation.
REMOVE BATTERY PACK
Locate latches of battery pack and depress both
■
sides to release the battery pack from the string
trimmer. See Figure 7.
Remove battery pack from the string trimmer.
■
REMOVING ADDITIONAL SPOOL FROM SPOOL
HOLDER
Turn the spool in the spool holder (Fig. 1 - B)
counterclockwise and pull the additional spool out of the
holder
14
RO PL SLO HR TR EST LT RO PL SLO HR TR EST LT
CAUTION
When placing battery pack in your string trimmer,
be sure raised rib on battery pack aligns with
groove in string trimmer and latches snap in
place properly. Improper assembly of battery
pack can cause damage to internal components.
LV LV SK BG SK BG