How To Replace The Vacuum Belt - Carpet Pro CPU-250 Owner's Manual

How to Replace the Vacuum Belt

CAUTION: First unplug the vacuum cleaner.
How to Remove the Bottom Plate
1� Place the vacuum cleaner in the lowest position by stepping on
the handle release pedal (see "How to Adjust the Handle" on
page 5)� Turn the vacuum over on a flat surface, exposing the
bottom plate�
2� Remove the five screws holding the L-shaped bottom plate in
place (Fig� 1)�
3� Remove the bottom plate�
How to Replace the Belt
1� Turn over the unit and remove the bottom plate as described
above�
2� Lift out the brushroll and remove the old belt (Fig� 2)�
3� Loop the new belt around the drive shaft (Fig� 3) and the raised
ring between the bristles on the brushroll (Fig� 4)�
4� Pull the brushroll forward (against the pull of the belt) and reinsert
the ends back into the nozzle (Fig� 5) making sure to line up the
end opposite the belt so the flat edges slide down properly�
5� Turn the brushroll by hand, making sure the belt is not twisted and
all rotating parts move smoothly�
6� Replace the bottom plate and the five screws�
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 7
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 7
Maintenance -
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 7
Changing the Belt
Maintenance -
If the brush bar stops rotating, it is likely that the
Changing the Belt
drive belt has snapped (usually because the
brush has been stalled). Replacement belts can
Maintenance -
be obtained from Morphy Richards by calling the
If the brush bar stops rotating, it is likely that the
Changing the Belt
spare parts helpline number: 0844 873 0726.
drive belt has snapped (usually because the
brush has been stalled). Replacement belts can
Accessing the floor nozzle
If the brush bar stops rotating, it is likely that the
be obtained from Morphy Richards by calling the
drive belt has snapped (usually because the Press the power pedal (26) to turn the cleaner off.
1.
spare parts helpline number: 0844 873 0726.
brush has been stalled). Replacement belts can
Disconnect the cleaner from the mains supply.
2.
Accessing the floor nozzle
be obtained from Morphy Richards by calling the
spare parts helpline number: 0844 873 0726. Press the upright release pedal (18) and place the
3. Press the power pedal (26) to turn the cleaner off.
1.
cleaner face down, in a flat position on a soft
Accessing the floor nozzle Disconnect the cleaner from the mains supply.
2.
surface (eg. carpet).
Press the power pedal (26) to turn the cleaner off.
1. Press the upright release pedal (18) and place the
3.
Removing brush bar and belt
cleaner face down, in a flat position on a soft
Disconnect the cleaner from the mains supply.
2.
Using a cross-headed screwdriver, unscrew the 5 surface (eg. carpet).
.
4
Press the upright release pedal (18) and place the
3.
screws on the base of the cleaner to release the
cleaner face down, in a flat position on a soft Removing brush bar and belt
L-shaped plate from over the rotary brush bar.
surface (eg. carpet).
Using a cross-headed screwdriver, unscrew the 5
.
4
screws on the base of the cleaner to release the
Removing brush bar and belt
L-shaped plate from over the rotary brush bar.
Using a cross-headed screwdriver, unscrew the 5
.
4
screws on the base of the cleaner to release the
Screw
L-shaped plate from over the rotary brush bar.
points
Screw
points
Screw
points
Remove the broken belt and lift out the rotary
5.
brush bar.
Remove the broken belt and lift out the rotary
5.
brush bar.
Remove the broken belt and lift out the rotary
5.
brush bar.
cleaner face down, in a flat position on a soft
Removing brush bar and belt
surface (eg. carpet).
Using a cross-headed screwdriver, unscrew the 5
.
4
Removing brush bar and belt
screws on the base of the cleaner to release the
Using a cross-headed screwdriver, unscrew the 5 L-shaped plate from over the rotary brush bar.
.
4
screws on the base of the cleaner to release the
L-shaped plate from over the rotary brush bar.
Remove the broken belt and lift out the rotary
5.
brush bar.
Remove the broken belt and lift out the rotary
5.
brush bar.
Refitting brush bar and belt
Hook the belt over the drive shaft (the belt must
6.
be slid sideways past the end of the drive shaft).
Refitting brush bar and belt
Hook the belt over the drive shaft (the belt must
6.
be slid sideways past the end of the drive shaft).
Refitting brush bar and belt
Hook the belt over the drive shaft (the belt must
6.
be slid sideways past the end of the drive shaft).
Pass the rotary brush bar through the belt,
7.
ensuring the correct end is located against the
belt.
Pass the rotary brush bar through the belt,
7.
ensuring the correct end is located against the
belt.
Pass the rotary brush bar through the belt,
7.
ensuring the correct end is located against the
belt.
Pull the rotary brush bar forward (against the pull
8.
of the belt) and locate the square ends of the
brush bar into location slots in the floor nozzle.
Pull the rotary brush bar forward (against the pull
8.
of the belt) and locate the square ends of the
brush bar into location slots in the floor nozzle.
Pull the rotary brush bar forward (against the pull
8.
of the belt) and locate the square ends of the
brush bar into location slots in the floor nozzle.
Rotate the brush bar by hand to ensure the belt is
9.
running in the centre of its location on the brush.
Refitting the floor nozzle base cover
Rotate the brush bar by hand to ensure the belt is
9.
Refit the L-shaped plate over the rotary brush bar,
.
10
running in the centre of its location on the brush.
and screw the 5 screws back into the base of the
Refitting the floor nozzle base cover
cleaner, using a cross-headed screwdriver, do not Rotate the brush bar by hand to ensure the belt is
9.
running in the centre of its location on the brush. overtighten the screws.
Refit the L-shaped plate over the rotary brush bar,
.
10
and screw the 5 screws back into the base of the
Refitting the floor nozzle base cover Return the cleaner to the upright position.
11.
cleaner, using a cross-headed screwdriver, do not
Connect to the mains supply. Switch on to test.
Refit the L-shaped plate over the rotary brush bar,
.
10
overtighten the screws.
and screw the 5 screws back into the base of the
Return the cleaner to the upright position.
11.
cleaner, using a cross-headed screwdriver, do not
Connect to the mains supply. Switch on to test.
8
overtighten the screws.
Return the cleaner to the upright position.
11.
Connect to the mains supply. Switch on to test.
Screw
points
Screw
points
Fig� 1
Fig� 2
Drive
shaft
Drive
shaft
Drive
shaft
Fig� 3
Fig� 4
Fig� 5
ensuring th
Pass the rot belt.
7.
ensuring the
belt.
Pull the rot
8.
of the belt)
Pull the rota brush bar i
8.
of the belt) a
brush bar in
Rotate the
9.
running in
Rotate the b
9.
Refitting
running in th
Refit the L-
.
10
Refitting t
and screw
Refit the L-s cleaner, us
.
10
and screw t overtighten
cleaner, usin
Return the
11.
overtighten
Connect to
Return the c
11.
Connect to
7
7
7
7