Lincoln Electric LF 52Ds Operator's Manual page 30

Loading the Wire Spool
Wire spool type S300 and BS300 can be installed on the
wire spool support without adapter.
Wire spool type S200, B300 or Readi-Reel
installed with use applicable adapter that must be
purchased separately (see "Accessories" chapter).
Wire Spool Type S300 & BS300 Loading
WARNING
Turn the input power OFF at the welding power source
before installation or changing a wire spool.

Turn the input power OFF.

Open the spool wire case.

Unscrew the Locking Nut [8] and remove it from the
Spindle.

Place the spool type S300 or BS300 [9] on the Spindle
[8] making certain the Spindle Brake Pin is put in the
hole in back side of spool type S300 or SB300.
WARNING
Position the spool type S300 or SB300 so that it will rotate
in the same direction as wire feed and electrode wire
should feed from the bottom side of the spool.

Install the locking nut [8]. Make sure that the locking
nut is tightened.
Wire Spool Type S200 Loading
WARNING
Turn the input power OFF at the welding power source
before installation or changing a wire spool.

Turn the input power OFF.

Open the spool wire case.

Unscrew the Locking Nut [8] and remove it from the
Spindle.

Place the adapter of spool type S200 on the spindle
[8] making certain the spindle brake pin is put in the
hole in back side of the adapter. The adapter of spool
type S200 can be purchased separately (see
"Accessories" chapter).

Place the spool type S200 [9] on the spindle [8]
making certain that the adapter brake pin is put in the
hole in the back side of the spool.
WARNING
Position the spool type S200 so that it will rotate in the
same direction as wire feed and electrode wire should
feed from the bottom side of the spool.

Install the locking nut [8]. Make sure that the locking
nut is tightened.
English
Wire Spool Type B300 Loading
®
can be Turn the input power OFF at the welding power source
before installation or changing a wire spool.

Turn the input power OFF.

Open the spool wire case.

Unscrew the Locking Nut [8] and remove it from the
Spindle.

Place the adapter of spool type B300 on the spindle
[9]. Make certain that the spindle brake pin is put in the
hole in the back side of the adapter. The adapter of
spool type B300 can be purchased separately (see
"Accessories" chapter).

Install the locking nut [8]. Make sure that the locking
nut is tightened

Rotate the spindle and adapter so the retaining
adapter spring of the adapter is at the 12 o'clock
position.

Place the spool type Readi-Reel
one of the spool wire inside in the groove of the
locking spring.
Position the spool type B300 so that it will rotate in the
same direction as wire feed and electrode wire should
feed from the bottom side of the spool.
Wire Spool Type Readi-Reel® Loading

Turn the input power OFF.

Open the spool wire case.

Unscrew the Locking Nut [8] and remove it from the
Spindle.

Place the adapter of spool type Readi-Reel
spindle [8]. Make certain that the spindle brake pin is
put in the hole in the back side of the adapter. The
adapter of spool type Readi-Reel
separately (see "Accessories" chapter).

Install the locking nut [8]. Make sure that the locking
nut is tightened.

Rotate the spindle and adapter so the retaining spring
of the adapter is at the 12 o'clock position.

Place the spool type Readi-Reel
one of the spool wire inside in the groove of the
locking spring.
Position the spool type Readi-Reel
the same direction as wire feed and electrode wire should
feed from the bottom side of the spool.
28
WARNING
® on the adapter. Set
WARNING
®
® can be purchased
®
on the adapter. Set
WARNING
® so that it will rotate in
English
on the