H&S 7116 Operator's Manual
  1. Manuals
  2. Brands
  3. H&S Manuals
  4. Farm Equipment
  5. 7116
  6. Operator's manual

H&S 7116 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
WARNING
Revision #01
7116 Ser. #911HCD6011
H&S MANUFACTURING CO.,INC.
HI-CAPACITY
7116
Manufactured By
2608 S. HUME AVE. MARSHFIELD, WI 54449
(715) 387-3414 | hsmfgco.com
RAKE
READ AND UNDERSTAND THIS MANUAL
BEFORE OPERATING THIS EQUIPMENT.
UNSAFE OPERATION OR MAINTENANCE OF
THIS EQUIPMENT CAN RESULT IN SERIOUS
INJURY OR DEATH.
HSMFG0420
Part #82874

Advertisement

Table of Contents
loading

Related Manuals for H&S 7116

Summary of Contents for H&S 7116

  • Page 1 BEFORE OPERATING THIS EQUIPMENT. UNSAFE OPERATION OR MAINTENANCE OF WARNING THIS EQUIPMENT CAN RESULT IN SERIOUS INJURY OR DEATH. Revision #01 HSMFG0420 Part #82874 7116 Ser. #911HCD6011 Manufactured By H&S MANUFACTURING CO.,INC. 2608 S. HUME AVE. MARSHFIELD, WI 54449 (715) 387-3414 | hsmfgco.com...

  • Page 2: Table Of Contents

    CONTENTS Warranty ..............1 Manufacturer’s Statement .
  • Page 6 Intentionally Left Blank...

  • Page 7: Dealer Pre-Delivery Checklist

    DEALER PRE-DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the rake has been completely set up, check to be certain it is operating correctly before deliv- ering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily.
  • Page 8 Intentionally Left Blank...

  • Page 9: Dealer Delivery Checklist

    DEALER DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS This check list that follows is an important reminder of valuable information that should be passed on to the customer at the time this Rake is delivered. Check off each item as you explain it to the customer. This delivery checklist, when properly filled out and signed, assures the customer that the pre-delivery service was satisfactorily performed.
  • Page 10 Intentionally Left Blank...

  • Page 11: Safety Information - Be Alert Symbol

    SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.

  • Page 12: Explanation Of Safety Signs

    SAFETY INFORMATION RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A signal word - DANGER, WARNING, or CAUTION - is used with the safety-alert symbol.

  • Page 13: Safety Decals

    SAFETY INFORMATION -11-...

  • Page 14: Safety Information - Warning - Owner Must Read And Understand

    TRACTOR: This operator’s manual uses the term “Tractor” when identifying the power source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.

  • Page 15: Cap Screw Torque Values

    -13-...

  • Page 16: Set-Up & Assembly

    SET-UP & ASSEMBLY NOTE: Determine the right or left side of the wheel rake by viewing it from the rear. If instructions or parts lists call for hardened bolts, refer to the Cap Screw Torque Value Chart. Assemble the rake or check the rake for proper assembly and adjustment. Make sure that all bolts are tightened.

  • Page 17: Transporting

    TRANSPORTING TRANSPORT LOCKS Latch System The Latch System (A) is mounted at the front of the pole. When the rake is in the transport position, make sure that the safety pin on each latch is placed in the hole (B) before transporting on the highway. Rake Wheel Locks Located on the lift pipe is a hair pin which is used to secure the rake wheels in the up position for transport (C).

  • Page 18: Preparing For Operation

    PREPARING FOR OPERATION 1. Adjust the tractor hitch (13 to 17 inches above ground) and attach the rake to the tractor with a hitch pin and a safety locking device. 2. Remove the weight from lift jack. Remove the jack from the pipe and place it on the convenient storage mount located on the front top of rake beam (A).

  • Page 19: Operation & Adjustments

    OPERATION & ADJUSTMENTS EMERGENCY SHUTDOWN Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning or working on the machine. Latch System The Latch System (A) is mounted at the front of the pole. When the rake is in the transport position, make sure that the safety pin on each latch is placed in the hole (B) before transporting on the highway.
  • Page 20 OPERATION & ADJUSTMENTS WINDROW WIDTH Windrow width adjustment is made by the ratchet jack located on the right rear of the rake as shown. An optional Hydraulic Cylinder Opening Windrow Width Adjustment is optional in place of the standard ratchet jack. This option requires a 3rd tractor remote. Windrow Width Adjustment Jack GROUND PRESSURE Rake wheel to ground pressure is adjusted...

  • Page 21: Optional Equipment

    OPTIONAL EQUIPMENT FFOHYDROP16 - HYDRAULIC OPENING WINDROW WIDTH ADJUSTMENT A Hydraulic Cylinder Opening Windrow Width Adjustment is optional in place of the standard ratchet jack. This option requires a 3rd tractor remote. The operator must be moving forward or backward when adjusting the hydraulic windrow width.

  • Page 22: Lubrication Guide

    LUBRICATION GUIDE GREASE FITTINGS There are numerous grease fittings on the rake. Lubricating properly and often enough will prolong the life of your rake. Grease daily during normal use and before and after storage and after power washing. Use a good grade of high quality grease. Make sure that grease comes out around the shaft on sleeve type bearings.
  • Page 23 LUBRICATION GUIDE Windrow Width Adjustment Windrow Windrow Rake Adjustment Rake Rake Cylinder/Jack Adjustment Backbone Pivot Jack Backbone Backbone Jack Rake Backbone One on each of the Cylinder Rake Arm Tube Sliders -21-...
  • Page 24 LUBRICATION GUIDE Linkage Pivot Jack OPTIONAL 3-WHEEL CENTER KICKER Grease the pivot points if your rake is equipped with a center kicker wheel. -22-...

  • Page 25: Decal Location

    WARNING - Stay Clear of Rake 21804 Attention - Never Adjust Main Frame 82303 H&S RH Branding 82304 H&S LH Branding 83198 Model Number-7116 11599 WARNING - Do Not Go Near Leaks 11694A DANGER - Stay Clear of Rake 12197A Attention: Raise Rake Wheels 54034 Made in the USA - 4”...
  • Page 26 DECAL LOCATION 2195 11694A 2195 093020 DCAMB 12197A 21804 11694A 71188B 11694A 11694A DCAMB 2195 11694A 72203A 84045 84044 54034 -24-...
  • Page 27 DECAL LOCATION Interior Left Rake Beam 11599 11599 2195 093020 11694A 11599 Interior Right Rake Beam 11599 2195 11599 11599 093020 11694A -25-...
  • Page 28 DECAL LOCATION Right Rake Beam w/Optional Front Caster 2195 83198 83203 093020 DCAMB 093020 2195 093020 093020 11599 093020 DCAMB 2195 11599 -26-...
  • Page 29 DECAL LOCATION Left Rake Beam w/Optional Front Caster 093020 DCAMB 2195 093020 83198 83204 093020 11599 2195 093020 DCAMB 093020 -27-...
  • Page 30 DECAL LOCATION Rear 11599 093020 83204 093020 093020 2195 DCRED 093020 DCRED 093020 -28-...

  • Page 31: Troubleshooting

    TROUBLESHOOTING WARNING: MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE RAKE CANNOT MOVE BEFORE SERVICING THE FLEX-FRAME RAKE. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY. POSSIBLE CAUSE POSSIBLE REMEDY TROUBLE Rake Will Not Open Rake Locked In Transport Remove Transport Locks And Return To Storage Position...
  • Page 32 TROUBLESHOOTING TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Rake will not rake crop Rake wheel ground pressure set Increase rake wheel ground too light pressure Not picking up crop in valleys Move caster wheels to center position Rake teeth wore out Replace rake teeth Rake banging as travelling Field too rough for single caster Add optional caster wheel...

  • Page 33: Service Notes

    SERVICE NOTES -31-...
  • Page 34 SERVICE NOTES -32-...
  • Page 36 H&S MFG. CO. products approved for the FEMA SEAL OF QUALITY...

Table of Contents