H&S GM 170 Operator's Manual And Parts List
  1. Manuals
  2. Brands
  3. H&S Manuals
  4. Farm Equipment
  5. GM 170
  6. Operator's manual and parts list

H&S GM 170 Operator's Manual And Parts List

Hide thumbs Also See for GM 170:
Table of Contents

Advertisement

Quick Links

WARNING
UNSAFE OPERATION OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN
SERIOUS INJURY OR DEATH
OPERA T T T T T OR'S MANU
OPERA
OPERA
OPERA
OPERA
H&S MANUFACTURING CO.,INC.
P.O. BOX 768 (715) 387-3414 FAX (715) 384-5463
GM 170
READ AND UNDERSTAND THIS MANUAL
BEFORE OPERATING THIS EQUIPMENT
OR'S MANU
OR'S MANU
OR'S MANU
OR'S MANU AL
AND
AND
AND
AND
AND
P P P P P AR
AR
AR TS LIST
AR
TS LIST
TS LIST
TS LIST
AR
TS LIST
Manufactured By
MARSHFIELD, WISCONSIN 54449
AL
AL
AL
AL
HSMFG0106

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GM 170 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for H&S GM 170

Summary of Contents for H&S GM 170

  • Page 1 GM 170 READ AND UNDERSTAND THIS MANUAL WARNING BEFORE OPERATING THIS EQUIPMENT UNSAFE OPERATION OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN SERIOUS INJURY OR DEATH OPERA OPERA T T T T T OR’S MANU OPERA OR’S MANU OR’S MANU...

  • Page 2: Table Of Contents

    H&S GM 170 OPERATOR’S & PARTS MANUAL CONTENTS Warranty & Warranty Registration Card..........1-2 Dealer Pre-Delivery &...

  • Page 3: Warranty & Warranty Registration Card

    WARRANTY H & S WARRANTY H & S Manufacturing Co., Inc. (“H & S”) warrants this product to be free from defect in material and workmanship. Except as noted below, this warranty term is twelve (12) months from the date of delivery of the product to the original purchaser by an authorized H &...
  • Page 4 IMPORTANT! Tear on dotted line, provide the information requested on the card. The H&S Warranty is valid “only” after this card is received and recorded at H&S Mfg. Co. Mail at once. No postage is required in the U.S.A. NO POSTAGE NECESSARY IF MAILED IN THE...

  • Page 5: Dealer Pre-Delivery & Delivery Checklist

    H&S DEALER PRE-DELIVERY CHECK LIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the 170 Grinder-Mixer has been completely set-up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily.

  • Page 7: Be Alert Symbol

    H&S DEALER PRE-DELIVERY CHECK LIST(CONT.) AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS SWINGING INTAKE AUGER (SIA)(if applicable) Guards, shields, and attaching hardware are in place and properly secured. SIA lifting, locking and supporting mechanisms function correctly. Counter-balance spring and brake are properly adjusted.

  • Page 9: Danger - Warning Signs

    SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.
  • Page 10 SAFETY INFORMATION RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A signal word- DANGER, WARNING, or CAUTION - is used with the safety-alert symbol.
  • Page 11 SAFETY INFORMATION...
  • Page 12 SAFETY INFORMATION -10-...
  • Page 13 SAFETY INFORMATION -11-...
  • Page 14 SAFETY INFORMATION -12-...

  • Page 15: Warning - Owner Must Read And Understand

    TRACTORS: This operators manual uses the term “Tractor” when identifying the the power source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.

  • Page 16: Bolt Torque Chart

    -14-...

  • Page 17: Preparing For Operation

    4. Maintain a distance of 6”- 12” between the top of the tractor drawbar and the center of the tractor PTO. An 8” distance is standard. Hydraulics The GM 170 requires a 4 hose hook-up; 2 hoses for the discharge auger lift, and 2 hoses for the discharge auger rotation. PREPARING MIXER * Properly lubricate the grinder-mixer, checking the transmission and cyclonic reservoir oil levels, and filling if necessary before operating the grinder-mixer.

  • Page 18: Set-Up & Assembly

    As necessary, drain the water before using the mixer. NOTE: After water has been drained from the mixer, it is advisable to run the GM 170 while empty for a period of time in an attempt to dry the mixer before grinding to eliminate any sticking of material and possible plugging.

  • Page 19: Transporting

    TRANSPORTING SMV BRACKET & REFLECTORS The grinder-mixer is equipped with a SMV bracket. Red reflector strips are located on the rear of the tank and on the SIA (if applicable). TRANSPORT LIGHTING An optional highway transport lighting kit is available. -17-...

  • Page 20: Operation

    OPERATION EMERGENCY SHUTDOWN In an emergency or in case a foreign object enters the mill inlet, stop mixer operation immediately by disengaging the tractor PTO. GENERAL INFORMATION Check entire unit carefully before first operation. Tighten bolts and set screws that might have come loose in shipping.
  • Page 21 OPERATION (cont.) CAPACITY The GM 170 mixing tank capacity is 170 cubic feet or 135 bushels by volume. The tank will hold approximately 6000 to 7000 lbs of ground feed consisting of average weight corn, small grain and/or concentrates. More or less weight (per tank) is possible, depending upon whether the material that is being ground is lighter or heavier than average.
  • Page 22 Hydraulic Pump/Motor Drive The GM 170 has a double sheave on the end of the main drive shaft which is connected by a double banded belt to the hydraulic pump.The pump is belt driven directly off the main drive shaft which is coupled by the telescoping drive to the tractor PTO shaft.
  • Page 23 OPERATION (cont.) Discharge Auger System Ground feed from the mixing tank is discharged by an auger system consisting of three hydraulically motor driven augers that are connected in series so that all augers are synchronized as well as started and stopped together. If any motor malfunctions, the movement of material through the augers will stop immediately.
  • Page 24 OPERATION (cont.) HYDRAULIC OPERATED ATTACHMENTS Swinging Intake Auger (SIA) An optional hydraulic drive Swinging Intake Auger (SIA) attachment conveys material into the mill. The intake auger can be swung in and locked against the mixer tank support brace for transporting, or swung out and locked at any point.
  • Page 25 The GM 170 can be fitted with numerous screens that are available with various size holes to accommodate different material and grinding requirements.
  • Page 26 OPERATION (cont.) OVERLOAD PROTECTION Main Drive The GM 170 is furnished with a 5/16 x 1: Grade 5 shear bolt protecting the transfer auger drive shaft, transmission and mixing auger. When the shear bolt fails, the transfer auger and mixing auger will stop turning.
  • Page 27 OPERATION (cont.) BLOWER INLET & OUTLET NOTE:The collector cover must always be open while grinding. Plugging in the blower inlet or outlet can be seen by the abnormal amount of dust particles in the air around the top of the collector, and/or the visible presence of dust in the mill throat area and/or a reduced air discharge at the top of the collector.
  • Page 28 OPERATION (cont.) MILL/BLOWER DRIVE BELT SLIPPAGE Overload protection for the mill and blower components is provided by an 8 “A” section drive belt, which connects the mill/blower driven sheave to the drive sheave. The mill and blower will gradually slow down without much reduction in tractor PTO speed if plugging develops from mill/blower drive belt slippage, and stop turning the mill/blower drive shaft if plugging or breakdown occurs in the mill or...

  • Page 29: Adjustments

    ADJUSTMENTS MILL/BLOWER DRIVE The combination mill/blower driven sheave is connected from the main drive sheave by an 8" “A” section banded drive belt. Adjusting bolts are provided to align the drive sheave with the driven sheave as well as to adjust the drive belt tension. Sheave Alignment To align the combination mill/blower driven sheave with the driven sheave, proceed as follows: 1.
  • Page 30 ADJUSTMENTS (cont.) FRONT DRIVE CHAIN The transfer auger/transmission shaft is driven by a sprocket which is connected by the front drive chain to a sprocket on the main drive shaft. The front chain tension is self-adjusted by a spring-loaded idler and does not require adjustment.
  • Page 31 ADJUSTMENTS (cont.) MILL SCREEN COVER LATCHES Over-center handle latches are used to secure the mill cover tightly closed while the mill is being operated. Lock nuts on the bolts of the latches are used to adjust latching tension. This tension should be adjusted and maintained so that some force has to be applied on the handles to lock and unlock them.

  • Page 32: Lubrication Guide

    LUBRICATION GENERAL INFORMATION IMPORTANT: The GM 170 must be properly lubricated, the transmission and cyclonic oil reservoir must be filled to the proper oil levels before it can be operated. IMPORTANT: Catch and dispose of fluid per local waste disposal regulations whenever service is performed on hydraulic components (valves, cylinders, hoses, etc.) or transmission.
  • Page 33 LUBRICATION (cont.) GREASING NOTE:Grease all fittings at the intervals of operation listed, before and after storing the unit, and as otherwise listed. Use a good grade of Lithium-base grease. Wipe dirt from the fittings before greasing to prevent the dirt from being forced into the bearing or pivot. Grease should come out around the shaft on sleeve type bearings.
  • Page 34 LUBRICATION (cont.) Telescoping PTO Drive (3 zerks) Auger/Transmission Main Flywheel (1 zerk) Shear Bolt-(1 zerk) Front & Rear Mill Bearings (2 zerks - remote in Grease Transfer Auger Front Bearing & Transfer Auger Rear Bearing Bank under main shaft shield) Shear Hub (under mill cover, 1 (1 zerk - remote on Main Shaft Slider Bearings...

  • Page 35: Service

    SERVICE HYDRAULIC SYSTEM Hydraulic Pump Sheave Alignment The hydraulic pump drive and driven sheaves must be maintained in correct alignment and be tightly secured at all times. Hydraulic Pump Belt Tension Overload protection for the hydraulic pump is provided by a self-adjusting spring tightener that requires no adjustment.
  • Page 36 SERVICE MAIN DRIVE SHAFT BEARINGS Main drive shaft bearings are greased by 2 of the remote zerks in grease bank under the step by the mill cover. For bearing replacement, follow steps 1-5 from the previous Belt Replacement section in this chapter.
  • Page 37 SERVICE MILL HAMMER ROTATION OR REPLACEMENT To maintain maximum grinding efficiency, the mill hammers should be rotated before wear radius measures ¼” (6 mm). Mill hammers are designed to be conveniently removed and rotated through 4 positions, before they require replacement. The hammers should be replaced when all four corners are worn to ¼”...
  • Page 38 SERVICE MIXING AUGER & TUBE The mixing auger should be centered inside the tube at all times. Adjustment bolts are provided on the 4 supports which hold the tube for aligning and centering it around the auger. Access to the adjustment bolts and removing the mixing auger is gained through the tank lid opening in the top of the tank.
  • Page 39 SERVICE Transfer Auger Shear Device The transfer auger shear bolts are accessible only through the mill cover. This shear bolt protects the transfer auger flighting. If the shear bolt fails, the transfer auger will stop rotating even though the mixing auger and transmission drive shaft will continue to rotate.
  • Page 40 SERVICE TRANSMISSION The GM 170 transmission can be removed from the mixer for taking it to the dealer for internal component service. Internal component repairs and replacement should only be attempted by (or under the direction of) an authorized H&S Manufacturing Dealer.

  • Page 41: Optional Features & Accessories

    SWINGING INTAKE AUGER (SIA) An optional Swinging Intake Auger(SIA) with a variable speed control is available for the GM 170. FENDER SET A fender set is available and consists of 2 fenders, 4 fender support angles and attaching hardware. Installation instructions are packaged with the kit of parts.
  • Page 42 OPTIONAL FEATURES & ACCESSORIES UNLOADING AUGER EXTENSIONS 3’ Folding Auger Extension The 3’ folding discharge auger extension kit consists of a 3’ length of auger which is attached on a pivoting mounting bracket to the end of the 12’ unloading auger. NOTE:The 3’...

  • Page 43: Troubleshooting Guide

    TROUBLESHOOTING NOTE:This Troubleshooting Chapter presents problems, causes and suggested remedies beyond the extent of loose, worn or missing parts and it was developed with the understand that the machine is in otherwise good operating condition. MILL & MIXER DRIVE PROBLEM CAUSE REMEDY PTO Shaft vibrates excessively.
  • Page 44 TROUBLESHOOTING MILL PROBLEM CAUSE REMEDY Decreased or low capacity Mill not operating at the Adjust tractor throttle to proper recommended RPM speed. RPM speed. Mill loses speed as material Adjust Mill/Blower sheave enters it. alignment and/or drive belt tension. Rotate or replace screen. Screen worn.
  • Page 45 TROUBLESHOOTING HYDRAULICS Note: In troubleshooting a self-contained hydraulic system, it is necessary to isolate the pump from the hydraulic motors to determine which unit is malfunctioning. A worn pump or motor will both give the same system indication. Run a pressure and flow check on the pump first to make sure that it is performing within the operating specifications, then check the motor for the correct specifications.
  • Page 46 TROUBLESHOOTING HYDRAULICS PROBLEM CAUSE REMEDY Tank unloads slow. Insufficient oil flow to motors. Increase tractor RPM speed. Plugged oil filter. Replace filter. Replace hydraulic pump. Hydraulic pump defective. Variable speed control valve not Open variable speed control valve more. open all the way. Hydraulic motor defective.
  • Page 47 TROUBLESHOOTING HYDRAULICS PROBLEM CAUSE REMEDY SIA turns too slow. Excessive or wet grain. The higher the moisture content and weight of the material that is being conveyed, the more power it takes. Adjust the variable speed control valve to allow more oil to the hydraulic motor.

  • Page 48: Decal Location & Identification

    DECAL PLACEMENT Your H&S 170 Grinder-Mixer was manufactured with operator safety in mind. Located on GM 170 are various decals to aid in operation, and to warn of danger or caution areas. Pay close attention to all the decals on your Grinder-Mixer.
  • Page 49 DECAL PLACEMENT 82907F 1494K 82907J 1494L 82907L 1494P 72203A 1494L 2595 11599 093466 82602 1494J 82602 GM-A & GM-B 82407 093366 1494A 82907D 093020 1494J Amber Reflector 1494K 82907I 82907E 9194A 093020 82907G 9194A 1 inside of cover, & 1 on top 112-11176 of cover -47-...
  • Page 50 DECAL PLACEMENT 82907E 82907M 093020 093020 11599 093020 11599 1494J 1494J 82907A 82907B -48-...
  • Page 51 DECAL PLACEMENT 11599 82407 9194A GM-A & GM-B 82907M 120-2177 82907C 82907D 5696D 5696E 32597A (Under Shield) 82602 82907C 82907D 82907H 82907C -49-...

  • Page 52: Instructions For Ordering Parts - About Improvements

    INSTRUCTIONS FOR ORDERING PARTS All service parts should be ordered through your authorized H & S dealer. They will be able to give you faster service if you will provide them with the following Model & Serial number is located on the main frame. All reference to left or right apply to the machine as viewed from the rear.

  • Page 53: Service And Parts Notes

    SERVICE & PARTS NOTES -51-...
  • Page 54 FIGURE 1 FRAME -52-...
  • Page 55 Figure 1 Frame ITEM # PART # DESC. GM72 Frame GM73 Hitch Shaft GM74 Hitch GM396 Jack 12N13 Jack Pin & Chain T151 1" Nut GM76 Tank Side Support GM77 Tank Back Support SMV Bracket GM78 Oil Tank Bracket GM79 Spindle Seal Inner Bearing...
  • Page 56 FIGURE 2 CONCENTRATE HOPPER COLLECTOR -54-...
  • Page 57 Figure 2 Concentrate Hopper Collector ITEM # PART # DESC. GM81 Dust Collector GM82 Dust Collector Cover GM83 Blower Pipe GM84 Cover Handle GM85 Dust Collector Pipe GM86 Cover Hopper GM420 Cover Seal GM87 Blower Transition Chute GM88 Stop Cover GM89 Supplement Hopper GM90...
  • Page 58 FIGURE 3 DRIVE LINE PUMP BELT DRIVE BELT -56-...
  • Page 59 Figure 3 DriveLine ITEM # PART # DESC. ITEM # PART # DESC. GM102 Mill Sheave 540 RPM GM424 1/4-28 Grease Line Adapter GM103 Mill Sheave 1000 RPM GM425 Grease Line 61" GM104 Key 3/8" Taper GM426 Grease Line 30" GM105 Seal (22338) GM427...
  • Page 60 FIGURE 4 MILL -58-...
  • Page 61 Figure 4 Mill ITEM # PART # DESC. ITEM # PART # DESC. GM133 Grinder Side Panel GM421 Bearing (J211WDN) GM134 Mill Bottom Panel GM419 1/8" Grease Line Adapter (244054) GM135 Mill Long Bolt 1/2" x 22.500" GM431 Locking Washer (WH-08) GM136 Screen Support GM432...
  • Page 62 FIGURE 5 MILL CYLINDER HAMMER REPLACEMENT DETAIL ITEM # PART # DESC. GM168 Mill Shaft GM169 Cylinder Key 3/8" X 19-3/8" GM170 Retaining Ring (EN237) GM171 Retainer Plate GM172 Cylinder Plate (12 Pcs.) GM173 Spacer GM174 Hammer Spacer GM175 Hammer ( 66 Pcs.) GM176 Cylinder Shaft Nut (N-12) GM277...
  • Page 63 FIGURE 6 INFEED CONVEYOR PIVOT ITEM # PART # DESC. ITEM # PART # DESC. GM203 Support LW131 1/2" X 3-1/2" Bolt GM204 Spring (40174) BFR119 1/2" X 2-1/4" Bolt GM205 Spacer 1/2" X 2" Bolt GM206 Spring Adjustment 1/2" Lock Nut GM207 Pivot Linkage X111...
  • Page 64 FIGURE 7 INFEED CONVEYOR -62-...
  • Page 65 Figure 6 Infeed Conveyor ITEM # PART # DESC. GM178 Shield T116 5/16" Nut RGB39 5/16" Lock Washer GM179 5/16" X 1" Carriage Bolt BFR22 1/4"-20 x 1/2" Set Screw 5B10 1/4" Key GM180 Spacer GM181 Motor Mount GM182 Handle Latch 1/8"...
  • Page 66 FIGURE 8 UNLOADING AUGER -64-...
  • Page 67 Figure 8 Unloading Auger ITEM # PART # DESC. GM220 Tank Unloading Auger GM221 Auger Drive Cap GM222 Auger Shaft GM223 Auger Tube GM224 Overflow Cover #60 Connector Link GM226 Sprocket 60-B11 GM227 Vertical Auger GM228 Clutch Plate GM229 Clutch Face GM230 End Cap Bearing GM231 Collar...
  • Page 68 FIGURE 9 CONVEYOR DRIVE -66-...
  • Page 69 Figure 9 Conveyor Drive ITEM # PART # DESC. ITEM # PART # DESC. GM141 Rod 3/8" X 21.875" Grease Zerk GM247 Sprocket 30T (540 RPM) WM29 Bearing (SA207-20G) GM248 Sprocket 54T (1000 RPM) F143 Flange (Greaseable) GM249 Shear Flange GM424 1/4"-28 Grease Line Adapter GM250...
  • Page 70 FIGURE 10 12' UNLOADING AUGER ITEM # PART # DESC. GM240 12' Auger Tube GM241 12' Auger GM242 Auger Bearing Shaft GM243 Spout GM244 Spout Rubber Bearing GM245 End Cap 5B10 1/4" Woodruff Key BFR22 1/4" Set Screw GM234 3/16" Rivet GM235 1/4"...
  • Page 71 FIGURE 11 3' & 6' AUGER EXTENSION ITEM # PART # DESC. GM278 6' Extension GM279 3' Extension GM280 6' Auger GM281 3' Auger GM282 Auger Connect Shaft GM283 Pivot Clamp GM284 Latch Clamp GM285 Latch Handle GM286 Latch Pivot Shaft GM287 Latch Rod GM288...
  • Page 72 FIGURE 12 TANK -70-...
  • Page 73 Figure 12 Tank PART # DESC. GM301 Tank GM302 Window GM303 Window Frame GM304 Motor Mount GM305 Lid Latch GM225 Latch Spring (A262) GM307 Lid Frame GM308 Lid Gasket GM309 I Bolt & Spring Assy. (A162 Spring) GM310 Lid GM3119 Decal (Bushel Scale) GM311 Mixing Auger GM312 Mixing Auger Tube...
  • Page 74 FIGURE 13 AUGER CIRCUIT -72-...
  • Page 75 Figure 13 Auger Circuit PART # DESC. 1/2 X 32" Hose Adapter (24FTX-S) Pipe Reducer (1 1/2 NPT TO 3/4) 1 1/2 X 64" Suction Hose Resevoir 3/4 X 3" Hose 3/4" Hose Barb LW288 Filter Head LW289 Filter Element GM10 3/4 Street Tee (3/4 MRO) GM11...
  • Page 76 FIGURE 14 AUGER SWING CIRCUIT ITEM # PART # DESC. Motor (Parker) TB0390FP100AAAB GM412 3/8" Nipple Nut (5404-6-6) 16SV351 3/8" Male Union Adapter DWM233 Needle Valve (F600S) CHM265 Elbow (6-6 CTX) GM42 3/8 X 264" Hose GM43 1/2 Male Coupler DWM205 Bushing 1/2"...
  • Page 77 FIGURE 15 AUGER LIFT CIRCUIT ITEM # PART # DESC. 10WR11A 2-1/2 X 16" Cylinder (645886) 23N234 3/8 Elbow DWM233 3/8 Male Union Adapter GM455 Restrictor (.032) DWM205 1/2 Male Coupler GM45 3/8 X 130" Hose GM46 3/8 X 125" Hose GM47 Adapter (0507-6-6) GM48...
  • Page 78 FIGURE 16 INFEED AUGER CIRCUIT ITEM # PART # DESC. GM52 1/2 X 81 1/4" Hose GM53 1/2 X 97 1/2" Hose GM17 Adapter (8 HTX) GM55 Tee (10 R6X) GM56 Elbow (10 C50X) GM57 Adapter (10 F50X) GM58 Pressure Tube GM59 Return Tube GM57...
  • Page 79 FIGURE 17 GEARBOX ITEM # PART # DESC. GM256 Gearbox Housing GM257 Side Cover GM258 Bottom Cover 12V66 5/16" x 3/4" GR 5 Bolt GM259 Bearing (6205C3) GM260 Bearing Lock Nut (N-06) GM261 Bearing Lock Washer (W-06) GM262 Input Shim GM263 Bevel Gear (Keyed) 12N21...
  • Page 80 FIGURE 18 SHIELDS ITEM # PART # DESC. GM321 Front Shield GM322 Shield Hinge RGB38 5/16" x 1" GR. 5 Bolt D110 1/4" x 1" GR.5 Bolt GM324 Flywheel Shield Lower GM325 PTO Guard GM326 Poly PTO Guard X192 Rubber Latch X195 Latch Pin GM327...
  • Page 81 -79-...
  • Page 82 FIGURE 20 OPTIONAL LIGHTS & FENDER -80-...
  • Page 83 Figure 20 Optional Lights & Fenders LIGHTS ITEM # PART # DESC. 56N154 Flasher Module Loom S441 Flasher Module GM330 Light Bracket Right GM331 Light Bracket Left 55N62 Light Housing Right 55N61 Light Housing Left S308 Rubber Grommet S309 Amber Hazard Light S310 Red Hazard Light MHD2...
  • Page 84 FIGURE 21 OPTIONAL SCALE ITEM # PART # DESC. GM400 Control Box Arm GM401 Control Box Mount GM119 U Bolt 5/16" x 2" GM402 Spindle Load Cell (146772) GM403 Hitch Load Cell (143480) GM404 Scale Display (400590) GM405 Power Cord GM406 Junction Box Cord GM407...

  • Page 85: Specifications

    H&S GM 170 Specifications Tank Capacity –Bushel Tank Capacity – Cubic Ft. Tank Diameter 72” Diameter of Mixing Auger 14” Diameter w/30” Base Ladder Standard -Front Mount Over Mill Tank Windows 2 Full Length & 1 Port Hole Style Overall Height 10’...
  • Page 86 H&S MFG H&S MFG ..CO H&S MFG CO ..H&S MFG H&S MFG products approved for the FEMA FEMA FEMA FEMA FEMA SEAL OF Q SEAL OF Q SEAL OF Q U U U U U ALITY ALITY ALITY ALITY...

Table of Contents