Page 1
OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN SERIOUS INJURY OR DEATH. IN SERIOUS INJURY OR DEATH. 3108 Starting Serial #911SS080001 3108 Starting Serial #911SS080001 3110 Starting Serial #911SS100001 3110 Starting Serial #911SS100001...
H&S reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products previously manufactured. Specifications, statements and descriptions of Products contained in this publication are subject to change without prior notification.
DEALER PRE-DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the Rake has been completely set up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily.
DEALER DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS This checklist that follows is an important reminder of valuable information that should be passed on to the customer at the time this Rake is delivered. Check off each item as you explain it to the customer. This delivery checklist, when properly filled out and signed, assures the customer that the pre-delivery service was satisfactorily performed.
SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.
SAFETY INFORMATION Keep signs in good condition. Immediately replace any missing or damaged signs. RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.
TRACTOR: This operator’s manual uses the term ″Tractor″ when identifying the power source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
SET-UP & ASSEMBLY NOTE: Determine right or left side of the Rake by viewing it from the rear. If instructions or parts lists call for hardened bolts, refer to the Cap Screw Torque Values page to identify. Assemble the Rake or check the Rake for proper assembly and adjustment. Make sure that all bolts are tightened.
TRANSPORTING TRANSPORT LOCKS There are two hydraulic transport lock valves on the rake that must be turned to the closed position during transport in case of tractor valve leakage, or hose breakage. TOWING ON HIGHWAY Follow state and local regulations when towing farm equipment on public highways. Never tow the rake on a public highway at a speed greater than 20 mph (32 kph).
PREPARING FOR OPERATION ADJUSTMENTS There are 5 sets of holes on the adjustable hitch. In addition, the hitch can also be flipped upside down to obtain 5 more positions, for a total of 10 positions to adjust for levelness. 1. Attach rake to tractor with a hitch pin that has a safety locking device.
OPERATION & ADJUSTMENTS EMERGENCY SHUTDOWN Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning or working on the machine. IMPORTANT: Retighten all bolts on the rake after 100 acres as bolts can loosen up on new machinery. Re-torque rake tooth bolts after first 100 acres.
Page 20
OPERATION & ADJUSTMENTS RAKE BEAM LEVEL ADJUSTMENT After the pole/tongue has been leveled and the rake lowered to the raking position, check the levelness of the right and left rake beams. If the rake beams are not level, follow the procedure below to adjust levelness: 1.
Page 21
OPERATION & ADJUSTMENTS FLOATATION & FLEXIBILITY Rake Wheels Each rake wheel oscillates independently through the wheel arm mount bolt with the slotted style hole. Rake wheel floatation pressure on either rake beam can be adjusted by turning the crank handle in either direction for heavier or lighter pressure.
OPTIONAL EQUIPMENT CENTER KICKER WHEEL An optional center kicker wheel is available. If the hay is laying out flat, the extra wheel allows you to raise the hay laying in the center of the rake out of the stubble for easier pick-up.
LUBRICATION Become familiar with all lubrication points and establish a routine to ensure complete lubrication of the rake. GENERAL INFORMATION IMPORTANT: Catch and dispose of fluid per local waste disposal regulations whenever service is performed on hydraulic components, valves, cylinders, hoses, etc. WHEEL BEARING LUBRICATION, CLEAN &...
Page 24
LUBRICATION (1) on each rake beam flex/pivot point - 2 total NOTE: LUBRICATION POINTS (1) on each rake ARE THE SAME ON THE RIGHT arm pivot point SIDE AS THE LEFT SIDE (2) 1 on the bottom of each ″ACTION″ pivot point (2) on the top of each...
Stay Clear of Rake 11599 Do not go near leaks 54033 U.S.A. 71188B Jack Storage Position 71565 Hydraulic Position Valve 72326 3108 Decal 72327 3110 Decal 72328 3112 Decal 69083 Action Rake Decal/Right 69084 Action Rake Decal/Left 82602 Crushing Hazard...
Page 27
DECAL LOCATION 2700A 11599 DCAMB DCAMB 82602 69083 72326 - 3108 72327 - 3110 72328 - 3112 2700B 093020 on each 093020 on each rake arm pivot point rake arm pivot point NOTE: DECALS & LOCATION ARE THE SAME ON THE RIGHT SIDE AS THE LEFT SIDE...
TROUBLESHOOTING NOTE: This Troubleshooting Chapter presents problems, causes, and suggested remedies beyond the extent of loose, worn, or missing parts. It was developed with the understanding that the machine is in otherwise good operating condition. WARNING: MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE RAKE CANNOT MOVE BEFORE SERVICING THE RAKE.
SPECIFICATIONS 3108 3110 3112 Number of Wheels....8 ....10....12 ..
Page 32
H&S MFG. CO. products approved for the FEMA SEAL OF QUALITY Manufactured by: H&S MANUFACTURING CO., INC. 2608 S. HUME AVE. MARSHFIELD, WI 54449 (715) 387-3414 | hsmfgco.com...