Table of Contents
Advertisement
Quick Links
OPERATOR'SMANUAL
WARNING
Revision #02
HT8 Starting Serial #021HT08001
H&S MANUFACTURING CO.,INC.
2608 S. Hume Ave. (715) 387-3414 FAX (715) 384-5463
HT8 TEDDER
Manufactured By
MARSHFIELD, WISCONSIN 54449
READ AND UNDERSTAND THIS MANUAL
BEFORE OPERATING THIS EQUIPMENT.
UNSAFE OPERATION OR MAINTENANCE OF
THIS EQUIPMENT CAN RESULT IN SERIOUS
INJURY OR DEATH.
HSMFG1019
Part #76937
Advertisement
Table of Contents
Related Manuals for H&S HT8
Summary of Contents for H&S HT8
- Page 1 UNSAFE OPERATION OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN SERIOUS WARNING INJURY OR DEATH. Revision #02 HSMFG1019 Part #76937 HT8 Starting Serial #021HT08001 Manufactured By H&S MANUFACTURING CO.,INC. 2608 S. Hume Ave. (715) 387-3414 FAX (715) 384-5463 MARSHFIELD, WISCONSIN 54449...
-
Page 2: Table Of Contents
CONTENTS Warranty................1 Manufacturers Statement . -
Page 4: Manufacturers Statement
MANUFACTURER'S STATEMENT Your New H&S Product has been manufactured of the finest quality materials and components. The performance you get from your machine is largely dependent upon how well you read and understand this manual and apply this knowledge. There is a right and a wrong way to do everything. Please do not assume that you know how to operate and maintain your Machine before reading this manual carefully. - Page 6 Intentionally Left Blank...
-
Page 7: Dealer Pre-Delivery Checklist
DEALER PRE-DELIVERY CHECK LIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the Tedder has been completely set-up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily. - Page 8 Intentionally Left Blank...
-
Page 9: Dealer Delivery Checklist
DEALER DELIVERY CHECK LIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS This check list that follows is an important reminder of valuable information that should be passed on to the customer at the time this Tedder is delivered. Check off each item as you explain it to the customer. - Page 10 Intentionally Left Blank...
-
Page 11: Safety Information - Be Alert Symbol
SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE. -
Page 12: Safety Information - Explanation Of Safety Signs
SAFETY INFORMATION RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A single word;... -
Page 13: Safety Information - Safety Decals
SAFETY INFORMATION -11-... -
Page 14: Safety Information - Warning - Owner Must Read And Understand
SAFETY INFORMATION TRACTORS This operators manual uses the term “Tractor” when identifying the power source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. -
Page 15: Cap Screw Torque Values
-13-... -
Page 16: Set-Up & Assembly
SET-UP & ASSEMBLY NOTE: Determine right or left side of the Tedder by viewing it from the rear. If instructions or parts lists call for hardened bolts, refer to bolt torque chart. Assemble the Tedder or check the Tedder for proper assembly and adjustment. Make sure that all bolts are tightened. -
Page 17: Transporting
TRANSPORTING TOWING ON HIGHWAY Follow state and local regulations when towing farm equipment on public highways. Never tow the Tedder on a public highway at a speed greater than 20 m.p.h. (32 kph). PTO HOLDER A convenient bracket is provided to hold PTO when Tedder is not in operation. Locking PTO onto holder will also prevent reel from turning during road travel. -
Page 18: Preparing For Operation
PREPARING FOR OPERATION TRACTOR CONNECTIONS Tractor Hitch 1. The hitch of the Tedder is designed for a standardized tractor hitch. Extend or shorten it so that the horizontal distance from the end of the tractor power takeoff shaft to the center of the hitch pin hole is 14 inches for 540 RPM PTO as shown in the drawing. An improperly located hitch point may cause damage to the universal joints of the power takeoff. -
Page 19: Operation & Adjustments
OPERATION & ADJUSTMENTS EMERGENCY SHUTDOWN Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning or working on the machine. REEL CAM ADJUSTMENT Your H&S Tedder delivers outstanding ground speed and yet gently fluffs up the hay. The height of hay pitching can be regulated by moving the adjustment lever (eight different settings), located on the left hand side of the Tedder. -
Page 20: Lubrication
LUBRICATION Become familiar with all lubrication points and establish a routine to ensure complete lubrication of the Tedder. GENERAL INFORMATION IMPORTANT: Catch and dispose of fluid per local waste disposal regulations whenever service is performed on hydraulic components, valves, cylinders, hoses, etc. WHEEL BEARING LUBRICATION/CLEAN/RE-PACK/ADJUSTMENT Grease wheel bearings as needed depending on amount of travel. - Page 21 LUBRICATION LOCATION OF GREASE FITTINGS A. (2) One at each end of PTO at U-joint C. One on hitch adjustment rod D. One on front jack shaft (sealed bearing) E. (2) One at each end of reel main shaft (sealed bearing) F.
-
Page 22: Decal Location & Identification
DECAL PLACEMENT Your H&S Tedder was manufactured with operator safety in mind. Located on the Tedder are various decals to aid in operation, and warn of caution areas. Pay close attention to all decals. DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED, OR IF THE TEDDER IS REPAINTED, REPLACE THE DECALS. - Page 23 DECAL PLACEMENT 12494D 12794 72203A 12494D 8477 1494L 1787G 2495 54033 DCAMB 8476 8477 12494D 1494J 1494K 3894 12494E 12494D 8476 1494K DCRED 1494J 12494D -21-...
-
Page 24: Instructions For Ordering Parts - About Improvements
INSTRUCTIONS FOR ORDERING PARTS All service parts should be ordered through your authorized H&S dealer. They will be able to give you faster service if you will provide them with the following Model & Serial number is located on the left front of the main frame of your unit. All reference to left or right apply to the machine as viewed from the rear. - Page 25 SERVICE NOTES -23-...
-
Page 26: Parts Notes
PARTS NOTES -24-... - Page 28 H&S MFG H&S MFG ..CO H&S MFG CO ..H&S MFG H&S MFG products approved for the FEMA FEMA FEMA FEMA FEMA SEAL OF Q SEAL OF Q U U U U U ALITY SEAL OF Q ALITY ALITY...