Table of Contents
Advertisement
Section 7: Features & Benefits
Section 7: Features & Benefits
Features
Surpassed rugged
industry standards
Factory assembled
5 Year gearbox warranty
Rugged heavy built gearboxes
Gearbox seal protection
2 Piece shield on wing gearboxes
LP Performance self-leveling hitch
Low hitch weight on tractor tongue
Narrow A-frame hitch
Adjustable park jack angle
Adjustable driveline hanger
Input driveline:
Cat. 6 CV or Cat. 5 Conventional
Drivelines with slip-clutches:
Cat. 5 intermediate
Cat. 4 wings
Grease zerks on end caps of
driveline cross journals
High blade tip speed
6" Blade overlap
3/16" Round stump jumper
Smooth top design
Deck sheet tops are 100% welded
Left wing rotates clockwise
1/4" Sidewall thickness
Beveled skid shoes on wings
LED signal lights
Hinged wing sections
1" Solid hinge rods
Wing transport locks
Enclosed dual leveling rods
5-Bolt hubs
Drain holes in wheel rims
Spring cushioned center-axle
Replaceable wheel spindles
Wheel options
LP Performance hitch option
Bar-tite hitch option
56
RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M
Table of Contents
RC3615 and RCM3615 Models
Rotary Cutters
All Land Pride
voluntary testing procedures according to ISO 4254-13.
Arrives for quick and easy set-up. Minimal time is wasted setting or prepping the unit.
Shows confidence in gearbox integrity.
Capable of handling heavy cutting applications.
Gearbox bottom seal protection for longer bearing life.
Driveline grease zerks are easier to access.
Reduces drawbar wear by keeping hitch level while going through ditches.
Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.
Allows for a tighter turning radius.
Park jack can be adjusted to be perpendicular to the ground.
Serves as a support rest for the driveline when the cutter is unhooked from the tractor.
Assist operator when attaching driveline to tractor power take-off shaft.
Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint
allows for 80 degree turns without doing damage to the driveline.
Driveline is sized right for the intended cutting capacity.
Slip-clutches will slip under load to minimize twist damage to driveline profiles.
Intermediate and wing driveline cross journals are easier to grease.
Allows clean cutting of material.
Eliminates skipping during turns.
Standard thick stump jumper material keeps damage to a minimum.
Reduces accumulation of debris and is easier and faster to clean.
Makes center decks and wing decks stronger.
Better discharge of material. Picks up tractor tracks.
Increased thickness reduces damage from objects being thrown into deck sidewalls.
Reduces gouging the ground when turning.
LED lights are bright, long lasting, and resistant to vibration, unlike incandescent
counterparts.
cutter
Allows
to follow terrain. Ideal for rough ground where hillsides, ditches, and
hollows can cause uneven cutting.
Larger diameter hinge rod gives greater strength to the
the hinge area itself.
Wing transport locks will hold wings in the folded position in the event of hydraulic loss.
utter
C
pulls equally on the rear axle while traveling over rough terrain.
5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Allows water to drain from wheels mounted on folded-up wings.
Helps prevent paint deterioration and rusting to the wheel rims.
Protects unit from bumps and ground shock.
Wheel spindles can be replaced when damaged without replacing entire axle assembly.
Laminated tires: Eliminates flats.
Air-filled tires: Give better cushion while transporting.
Foam-filled tires: Give better cushion while transporting and can't go flat.
Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and
pivots about the tractor drawbar.
Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
Benefits
have been designed and tested and meet rigorous
cutter
from front to rear, and in
12/12/18
Advertisement
Table of Contents
