Page 1
Table of Contents Rotary Cutters RC3615 and RCM3615 Series 2 S/N 945023+ 37570 330-502M Operator’s Manual Read the Operator’s Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Cover photo may show optional equipment not supplied with standard unit.
Machine Length Machine Width Machine Weight Delivery Date First Operation Accessories Dealer Contact Information Name: Street: City/State: Telephone: Email: California Proposition 65 WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 3
Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Page 4
Download the appropriate App on your Refer to Parts Manual QR smart phone, open the App, point your Locator on this page for phone on the QR code and take a picture. detailed instructions. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Important Safety Information Important Safety Information Listed below are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Look for the Safety Alert Symbol Careful operation is your best The SAFETY ALERT SYMBOL indicates there is a assurance against an accident.
Lower implement to the ground and Replace parts on this implement implement. follow all shutdown procedures with genuine Land Pride parts only. Attach the chain to the tractor before leaving the operator’s seat to Do not alter this implement in a way drawbar support or other specified perform maintenance.
Page 7
Use Seat Belt and ROPS signals are recommended Keep Riders Off whenever driving on public roads. Machinery Land Pride recommends the use of a CAB or roll-over-protective- Never carry riders on tractor or structures (ROPS) and seat belt implement.
Some new equipment installed during repair requires with a similar type of straight edge. safety labels to be affixed to the replaced component as 37586 818-830C Safety Combo: 2 - Places: Right and left wings RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 9
1-Place (Top of splitter shield) 3-Places (Main driveline and 2-wing drivelines) 37586 818-142C Danger: Rotating Driveline - Keep Away (3-Places) Located on right wing, left wing, and center deck gearbox shields 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 10
Located on the back center axle 37588 818-130C RC Series cutters only Caution: Use 540 rpm power take-off 818-240C RCM Series cutters only Caution: Use 1000 rpm power take-off 37588 818-714C Danger: Crushing Hazard RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 11
Danger: Guard Missing - DO NOT Operate (3-Places) Located on center deck and both wing decks 37588 818-276C Warning: Rotating Blade Hazard (1-Place) Located on left side of center deck 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 12
818-561C Danger: Raised Wing Hazard (2-Places) Located on the right and left wing decks 37586 818-556C Danger: Thrown Object Hazard (2-Places) Located on the right and left wing decks RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 13
Important Safety Information 37586 818-564C Danger: Rotating Blade (2-Places) Located on the right and left wing decks 37588 838-094C Warning: High Pressure 37588 838-588C Warning: Folding Cutter Speed Warning 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 14
2" x 9" Red Reflector Located on back side of left & right wing rear axles 37586 838-615C 2" x 9" Amber Reflector Located on front side of left wing only. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
& noted before continuing. Salina, Ks. 67402-5060 NOTE: A special point of information that the E-mail address operator should be aware of before continuing. lpservicedept@landpride.com 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Make sure all pneumatic tires are properly inflated Power Take-Off to Drawbar Distance and all wheel bolts and axle nuts are tightened to Page 58 Figure 1-1 the specified torque. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Refer to Figure 1-6: Cutter rotation about the tractor drawbar is limited to movement about the pintle connection. The pintle hitch is ideal for a drawbar hammer strap. Pintle Hitch Figure 1-6 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
6. Wait for all components to come to a complete stop before leaving the operator’s seat. Use steps, grab-handles and anti-slip surfaces when stepping on and off the tractor. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
10. Attach cutter to tractor drawbar with customer supplied hitch pin (#1) and hairpin cotter (#2). 11. Lower park jack (#3) until hitch weight is supported by drawbar. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 20
(#9). 18. Continue with “Hydraulic Hook-up” on page 18. Shut tractor down properly before dismounting. Refer to “Tractor Shutdown Procedure” on page 14. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
2. Secure hydraulic hoses together with zip ties (#12) as needed to keep them from pinch areas caused by raising and lowering the deck, folding the wing up and down, and while making turns with the tractor. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
8. Tighten locknuts (#2) until snug. Do not over tighten. Wing axle must be able to pivot in the field. Transport Bar, Storage Position 9. Repeat steps 4-6 for the left wing axle. Figure 1-15 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
If park jack (#7) is attached to the hitch, it should be removed and stored on the left-hand wing. For detailed instructions, see steps 11-12 on page 15. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 26
11. Tighten 3/8"-16 GR5 bolts (#3) to the correct torque. Figure 1-20 IMPORTANT: Always rotate driveline hanger down before moving cutter to prevent damage to driveline. 12. Rotate driveline hanger (#1) down. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
5. Repeat steps 1 & 2 above once air is purged from the deck lift hydraulic system. 6. Tighten hose fitting (#5) at lift cylinder (#4). 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 28
LED Hookup (Standard Clevis Hitch Shown) 6. Add cable ties (#15) to wire harness as needed to Figure 1-22 secure the harnesses in place. Tractor 7-Pin Electrical Outlet Figure 1-23 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 29
Remove and discard all four shipping lugs (#1) and attaching hardware (#2 & #3). Remove Rear Shipping Lugs Figure 1-24 39038 Remove Front Shipping Lugs Figure 1-25 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
12. Move cylinder lift levers back and forth to release all Hydraulic Lift Cylinder With Stroke Control Spacers hydraulic pressure at the couplers. Figure 1-28 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 31
(#9) with removed bolt (#1) and locknut (#2) Screw locknut on 4 or 5 full turns. Do not torque nut tight. Unhook Bar-Tite Hitch Figure 1-31 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
1" with the front folded up. See cover picture for correct positioning. being closer to the ground than the back. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 33
If outer wing edge is lower than the center deck, loosen jam nut (#1) and rotate turnbuckle (#2) clockwise to raise outer wing edge until wing is level. Tighten jam nut (#1) to the correct torque when level. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 34
Two 1" spacers • One 1 1/4" spacer • One 1 1/2" spacer • One 1 3/4" spacer NOTE: Removing spacers lowers cutting height and adding spacers raises cutting height. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
A person can become entangled in the drivetrain if the tractor is started and the power take-off is engaged. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Exceeding rated cutting capacity can damage drive • Check for and remove foreign objects wrapped components, cutter blades, and deck components. around blade spindles. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Tractor power take-off shaft shield, driveline shields, and gearbox shaft shields must be installed and in good working condition to avoid driveline entanglement and projectiles flying off of the driveline. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Refer to “Safety Guards” on page 37. the Rotary Cutter is 20 mph. DO NOT EXCEED. Use the LED flashing lights on the cutter to make yourself more visible when cutting road sides. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Make a new gear selection if tractor is lugging 4. Remove hairpin cotters (#1) from both left and right down or if cutter is making a rough cut. wing cylinder pins (#4). 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 40
You should now be ready to transport to your cutting site at a safe ground speed. On roadways, transport in such a manner that faster moving vehicles can easily see you RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
8 - Wheel axle arrangement: Four tires on transport rotation if someone is in or around the area. axle and two on each wing axle. Land Pride offers three types of safety guards to best suit Hitches your application: rubber skirt guards, single row chain The cutter is factory supplied with the standard clevis guards, and double row chain guards.
Page 42
Remove transport lock and lower wing deck with mechanical winch. c. Tighten hydraulic fitting and connect all hydraulic hoses to a tractor. d. Purge hydraulic system of air. See “Purge Hydraulic System” on page 23. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Replace tractor hydraulic filter element at the prescribed intervals. These simple maintenances will go a long way to prevent occurrence of control valve and hydraulic cylinder problems. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Never try to straighten a bent blade! Small nicks can be ground out when sharpening. Refer to Figure 5-6 on page 43 when ordering Land Pride replacement blade components. Remove cutting blades and sharpen or replace as follows: Park on a level, solid surface.
Page 47
(#8) with both legs bent opposite directions around the nut. 13. Replace rubber plug (#5). Direction of Blade Rotation 14. Reconnect main driveline to tractor power take-off Figure 5-7 shaft. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
8. The clutch should be checked during the first hour of cutting and periodically each week. An additional set of scribe marks can be added to check for slippage. See Figure 5-11 on page 45 to adjust spring length. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 49
Place springs (#2) over the bolts and secure with nuts (#1). Refer to Figure 5-11: Progressively tighten each spring retainer bolt until correct spring height “A” is reached. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 50
3 and 1/6 revolutions, “B” = 5.5 mm (0.217”). If a higher torque is needed, then tighten nuts another 1/6 of a revolution, Do not set gap “B” smaller than 5 mm (0.197"). RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Store cutter on a level surface in a clean, dry place. Inside storage will reduce maintenance and make for a longer cutter life. 8. Follow “Unhook Rotary Cutter” instructions on page 26 when disconnecting tractor from cutter. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Repack wheel bearings annually 27926 Hours Adjustable Turnbuckle Type of Lubrication: Multi-Purpose Grease Quantity = As required 37580 Hours Hitch Frame Type of Lubrication: Multi-Purpose Grease Quantity = As required RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 53
Quantity = As required 37725 Needed Park Jack 1 - zerk Type of Lubrication: Multi-purpose Grease Quantity = As required Frequency = As needed and when unhooking for longterm storage. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Reinstall and tighten oil level plug and oil fill/vent plug. Type of Lubrication: 80-90W EP Quantity = Fill until oil begins to flow out oil level plug hole in gearbox. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 55
Zerk located through slot in plastic outer tubes Hours Conventional Main Driveline Profile Tubes Type of Lubrication: Multi-purpose Grease Quantity = Coat Generously 23567 Hours Conventional Main Driveline Joints & Shields Type of Lubrication: Multi-purpose Grease 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Page 56
Grease fittings located on the u-joints and driveline Attach safety chain (#2) to cutter frame. shields should be lubricated every 8 Hrs of operation. CV Driveline with overrunning clutch Figure 5-14 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 57
Steps 1-6 can be repeated to lubricate universal joint 3. Refer to Figure 5-19: Pull back on driveline shielding on opposite end of driveline. until CV joint is exposed. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
8 - Wheel option: Four on transport axle and two on each wing axle. Transport axle Spring-cushioned on center transport axle Hubs Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts. Deck rings Optional RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Page 59
Transport Width Transport Width With Wing Axles Disconnected Without Special Adjustments At Turnbuckles (#5) And Wheels Folded Back (See Figure 1-13 on page 19) 27930 15'- 11 1/2" 27931 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and LP Performance hitch option pivots about the tractor drawbar. Bar-tite hitch option Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear. RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M 12/12/18...
Blades have unequal weight Replace each pair of blades on affected carrier. Wing cylinder movement too slow Orifice is plugged Remove elbow fitting and unplug orifice. 12/12/18 RC3615 and RCM3615 Series 2 S/N 945023+ Rotary Cutters 330-502M...
This Warranty is limited to the repair or replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part, and does not cover common wear items. Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.