Related Manuals for ZKTeco FaceKiosk-H13 Series
Summary of Contents for ZKTeco FaceKiosk-H13 Series
- Page 1 Quick Start Guide FaceKiosk-H13 Series Version: 2.2 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
- Page 2 1. Components FaceKiosk-H13A Visible Light Camera Near Infrared Camera Near Infrared Fill Light Near Infrared Fill Light LED Fill Light LED Fill Light Speaker Speaker IC Card Reading Area Fingerprint Scanner /QR Code Scanner 13.3-inch High-definition Capacitive Touch Screen...
- Page 3 FaceKiosk-H13C/FaceKiosk-H13C[TD] Thermal Infrared Temperature Antenna Measurement Module Near Infrared Fill Light Near Infrared Fill Light LED Fill Light LED Fill Light Visible Light Camera Near Infrared Camera 13.3-inch High-definition Capacitive Touch Screen Speaker Speaker Fingerprint Scanner IC Card Reading Area QR Code Scanner Ticket Printer Base...
-
Page 4: Product Interface
2. Product Interface The terminals on the back of the FaceKiosk-H13 series are the same. Connecting Terminal Video Out Port Network Port Power Interface SIM Card Slot USB Port Reset Button USB Port On the back of the device, there are five rows of slots, which are J1, J2, J3, J4, and J5 from left to right. -
Page 5: Installation Procedure
3. Installation Procedure FaceKiosk-H13A Before installation, connect the wire to the device and move it through the device’s lower aperture. Align the backplate to the screw holes on the back of the device. Secure the plate with the screws (11 pcs) to the back of the unit. Place the rear panel at an appropriate height from the ground. - Page 6 Set the device at the desired position on the rear panel that is fixed on the wall. Secure the Kiosk by assembling the device and the rear panel with the bottom screw.
- Page 7 FaceKiosk-H13C/FaceKiosk-H13C[TD] 2. Installation Procedure Before installation, connect the wire to the device and move it through the device’s lower aperture. Take the device and the base from the box. Fix the device into the corresponding slot of the base plate. Take the FaceKiosk-H13C[ TD] as an example: Cautiously incline the device horizontally and assemble the device over the base with the screws (8 pcs) from the bottom of the base.
- Page 8 Place the device in the right position and remove the four screws that secure it to the base, remove the metal cover. Drill holes with an electric drill, implant two screws into the ground to fix the device, then cover back the metal cover, and finally tighten the four screws.
- Page 9 4. Door Sensor, Exit Button & Alarm Connection Power ElectricLock FR107 5. Access Control Device Connection RS232 Access Control Device Wiegand reader 485 reader...
- Page 10 6. 4G, Ethernet and WiFi Connection 4G Connection Open the back cover of the device, insert the SIM card, and the device will be automatically configured for 4G network. LAN Connection Plug in the network cable. Then set the network parameters on the device. Network cable Wi-Fi Connection Tap [System Settings] >...
-
Page 11: Interface Introduction
7. Interface Introduction The status of the connection between the device and the server, if the connection is not successful, a red flag will be displayed. Tap on to view the device information and the hardware module connection status. Tap on to open the QR Code self-registration. Tap on to change the software language. -
Page 12: Operational Procedure
8. Operational Procedure Visitor Self-registration Methods 1) Register on the reception desk device. 2) Scan the QR Code to register via Mobile phone. Note: The visitor can register by scanning the QR Code on the reception desk device or the QR Code on the invitation E-mail sent by the system in advance. - Page 13 9. Clear the Data Tap on [System Settings] > [Common Settings] > [Exit]to exit the software.In the Android system settings, find the two APKs in the application center, and click clear data to clear the cache. Common Settings Date and Time User Management Restore All the Settings AD Settings...
-
Page 14: Software Basic Settings
10. Software Basic Settings Internet After completing the following simple steps, the device will be ready to use for visitor management. Settings on Device Tap on [System Settings] > [Communication Settings] > [Ethernet Setting] to set the network parameters. Tap on [System Settings] > [Communication Settings] > [Software Server Setting]to set the server address and server port, that is, the IP address and port number of the server after the software is installed. - Page 15 Ethernet Setting Enable Ethernet User Management DHCP Manual AD Settings 192.168.163.99 IP Address Subnet Mask 255.255.255.0 Record Search Gateway Address 192.168.163.1 Data Management 114.114.114.114 TCP Comm. Port 4370 System Settings System Infirmation Software Server Setting Server Type ZKBioSecurity User Management Server Address 192.168.161.12 Manual...
- Page 16 Settings on ZKBioSecurity Add the device to the FaceKiosk Module of the software. Open the ZKBioSecurity software then select [FaceKiosk] > [Device] > [Search] > [Add]. Device Name Device Serial Number Step 1 Search Criteria None FaceKiosk Device Refresh Delete Search Control View/Get Clear Device Data...
- Page 17 Port E-mail Management yang@zkteco.com Email Account Dictionary Management Step 3 ....... Password Data Cleaning Sender Name Audio File Data Migration Step 5 Certificate Type Print Template System Monitoring Close Parameters Note: For details, please refer to FaceKiosk-H13 Series User Manual.
- Page 18 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 : +86 755 - 89602394 www.zkteco.com Copyright © 2022 ZKTECO CO., LTD. All Rights Reserved.