Advertisement
Wiring
Wire the Heartland Timer to the tanning bed. Apply power to the T-Max 3A as described in their
Wire the Heartland Timer to the tanning bed. Apply power to the T-Max 3A as described in their
respective User's Guides.
Run the provided modular cable from the tanning room to the remote T-Max 3A or T-Max 1A.
Run the provided modular cable from the tanning room to the remote T-Max 3A or T-Max 1A.
Connect the modular cable to one of the RJ-22 ports on the Heartland Timer and T-Max 1A or T-
Max 3A (see RJ-22 ports for T-Max Series timers on page 16, figure B).
Configuration
Set the address on the Heartland Timer in the tanning room to 1. Set the address on the T-Max 3A
Set the address on the Heartland Timer in the tanning room to 1. Set the address on the T-Max 3A
to 0.0. For setting the delay refer to the T-Max 3A user's guide.
Note: When setting the address on the Heartland Timer in the tanning room, the power to the front
desk T-Max 1A or 3A must be off.
Session Control
Session Control
Starting a session
Starting a session
1. 1. Press the Up and Down button on the T-Max 3A or the Set button on the T-Max 1A at the front
desk until the session time is displayed. Time cannot be set from the Heartland Timer in the room.
2. Press the Start/Stop button on the front desk T-Max 1A or T-Max 3A to start the session.
2. Press the Start/Stop button on the front desk T-Max 1A or T-Max 3A to start the session.
If a delay other than 0 is set, the delay will count down. A period on the lower right corner of the
If a delay other than 0 is set, the delay will count down. A period on the lower right corner of the
display will flash rapidly. When the session starts, the period will flash at once per second rate.
If a 0 delay is entered, the session will start immediately.
Pause during the Session
To pause the session press the Start/Stop button on the Heartland Timer in the tanning room. The
flashing period on the lower right corner of the display will stop flashing and stay illuminated. To
restart the session, press the Start/Stop button on the Heartland Timer
in the tanning room. The period will continue flashing.
Note: The session time will continue to count down. The display will continue to update and reflect
the remaining session time.
Canceling a session
To cancel a session, press both the Start/Stop band Up button on the T-Max 3A at the front desk
To cancel a session, press both the Start/Stop band Up button on the T-Max 3A at the front desk
simultaneously. If you are using a T-Max 1A, press the Start/Stop and the Set buttons simultane-
ously. The session cannot be canceled from the Heartland Timer.
USING THE HEARTLAND TIMER WITH A T-MAX MANAGER OR T-MAX MANAGER/PLUS/PRO
If you are using Heartland Timers with a T-Max Manager or T-Max Manager/Plus, follow these
If you are using Heartland Timers with a T-Max Manager or T-Max Manager/Plus, follow these
instructions for proper operation:
instructions for proper operation:
If you need to set the address on the Heartland Timer manually, be sure to set each Heartland
Timer to a different address. No Heartland Timer should be set to address 00.
Connect each Heartland Timer together using a modular cable that conforms to the pinouts shown
Connect each Heartland Timer together using a modular cable that conforms to the pinouts shown
on Figure B. Connect T-Max Manager or T-Max Manager/Plus to the closest Heartland Timer in
the line (refer to Figure C).
Note: Delay is controlled by the T-Max Manager, the T-Max Manager/Plus or the software you
are using if you are using a computer. It is not necessary to set the delay on the Heartland Timer.
Refer to the T-Max Manager or T-Max Manager/Plus User's Guide for operation.
www.heartlandtan.com
15
11/05
Advertisement
