Advertisement
Note: If you are using the Heartland Timer as an independent timer, you don't need to set the address on the Heartland
Timer.
1. Press and hold the Start/Stop buttons simultaneously on the Heartland Timer until a .1 appears on the dis-
play. Release the buttons. This should take about 5-6 seconds.
2. Press and release the Start/Stop button. A number will appear on the display and be flashing. A period will
be illuminated in the center of the display. Pressing and holding the Up button will cause the display to count
up. Once the count reaches 100, the center period will flash rapidly. This is an indication that you are over
99. For example, if the display shows a 0.2 with the period flashing, this is address 102. The highest the dis-
play will count up is 254.
3. Press the Up and Down buttons until the desired address is displayed. When setting the address, remember
3 rules:
A) Set each Heartland Timer to a unique address. B) Do not set any address to 0.
C) Do not set any address over 100.
4. Press the Start/Stop button. The ".1" will appear on the display. The 1 will not be flashing.
5. To exit, press and hold both Up and Down buttons until the display shows a 0 with no periods displayed.
Table 1 - Parameter numbers for observing and changing parameters.
Param.#
Param.#
Param.#
Param.#
Param.#
Description
Description
Description
Description
Description
Salon Level
Salon Level
1
1
1
1
1
Address
Address
Address
Address
Address
2
2
2
2
2
Beep Mode
Beep Mode
Beep Mode
Beep Mode
Beep Mode
3
3
3
3
3
Delay Time
Delay Time
Delay Time
Delay Time
Delay Time
5
5
5
5
5
Session
Session
Session
Session
Session
6
6
6
6
6
Lamp Hours
Lamp Hours
Lamp Hours
Lamp Hours
Lamp Hours
7
7
7
7
7
Bed Hours
Bed Hours
Bed Hours
Bed Hours
Bed Hours
8 8
Manual Session Counts
Manual Session Counts
9
9
9
9
9
Clean Room
Clean Room
Clean Room
Clean Room
Clean Room
10
10
10
10
10
Manual Lockout*
Manual Lockout*
Manual Lockout*
Manual Lockout*
Manual Lockout*
13
13
13
13
13
Cool Down Mode
Cool Down Mode
Cool Down Mode
Cool Down Mode
Cool Down Mode
14
14
14
14
14
5 Min. Beep
5 Min. Beep
5 Min. Beep
5 Min. Beep
5 Min. Beep
15
15
15
15
15
Fixed Session
Fixed Session
Fixed Session
Fixed Session
Fixed Session
16
16
16
16
16
Pulse Mode
Pulse Mode
Pulse Mode
Pulse Mode
Pulse Mode
17
17
17
17
17
Clean Clear
Clean Clear
Clean Clear
Clean Clear
Clean Clear
18
18
18
18
18
Redisplay
Redisplay
Redisplay
Redisplay
Redisplay
19*
19*
Third Part Interface
www.heartlandtan.com
SETTING THE ADDRESS
Max #
Max #
Max #
Max #
Max #
Default
Notes
128
128
128
128
128
1
1
1
1
1
Set this number to the room number you want the timer to be
1
1
1
1
1
0
0
0
0
0
Used for High Power beds. 0=Alarm Only, 1=Alarm and Flip
10
10
10
10
10
3
3
3
3
3
Delay in minutes stored in the Heartland Timer
65535
65535
65535
65535
65535
0
0
0
0
0
Total Session counts for Heartland Timer Counts
65535
65535
65535
65535
65535
0
0
0
0
0
Bulb hours for each bed
65535
65535
65535
65535
65535
0
0
0
0
0
How may hours a bed is on
65535
65535
0
0
Counts the # of sessions the Heartland Timer Session has run
while in Stand Alone Mode
1
1
1
1
1
1
1
1
1
1
0 = Clean Room Disabled. 1 = Enabled
1
1
1
1
1
0
0
0
0
0
0 = Stand Alone Enabled. 1 = Disabled
10
10
10
10
10
3
3
3
3
3
0 = Disabled, 1-10 = Enabled. Time delay in minutes allowing bed to cool.
The fans will remain running while the Heartland Timer is in cool down mode.
1
1
1
1
1
0
0
0
0
0
0 = Disabled, 1 = Enabled. Heartland Timer will beep for 10 seconds every 5 minutes
Counts number of sessions ran through the TMax ® 3A.
65535
65535
65535
65535
65535
0
0
0
0
0
This value cannot be changed at all. Used as point of reference.
0 = Disabled, 1 = Enabled. When session starts, the relay on the T-Max ®
1
1
1
1
1
0
0
0
0
0
1A will close for 1-2 seconds then open.
1
1
1
1
1
0
0
0
0
0
0 = Press and hold the Set button for 3-4 seconds to clear the clean room.
1 = Press and release the Set button to instantly clear the clean room.
2
2
2
2
2
0
0
0
0
0
0 = After a session ends and the clean room is cleared, the Heartland Timer will
show a 0. 1 = After session ends and the clean room is cleared,m the Heartland
Timer will show the last session time entered. 2 = After the session ends and the
clean room is cleared, the max. time will show on the Heartland Timer.
1
1
1
0
0
0
When set to a 1, voltage must be applied be an outside source to the TPI
input on the back of the Heartland Timer. Used is the timer is being controlled
by either a FST ® or Database
13
®
® or Database
® Series Timer. See Section for JPI settings
®
® 3A.
11/05
Advertisement
