Page 2
WELCOME TO THE FAM Congratulations on the purchase of your new Shuttle MVP. Shuttle equipment has been trusted by physical therapists and sports training facilities around the globe for almost half a century. It is our mission to deliver the finest quality exercise devices with superior customer service.
IMPORTANT SAFETY INFORMATION ..…………………………………………………………….…………. 1 PERSONAL SAFETY ……….……………………………………………………………………….……………. 1 SPECIFICATIONS ………………………………….………………………………………..…………..……….. 2 IDENTIFICATION OF THE MANUFACTURER …………………………………………………….……….…. 2 ASSEMBLY OF THE MVP ………………………………………………………..……………………………… 3 - ASSEMBLY OF MVP RAILS…………………………………………………………..4 - ATTACHING THE HEAD-END STAND………………………………………..……5 - ATTACHING THE KICKPLATE STRUCTURE………………………………………..6 - INSTALLING THE REBOUND STOP BLOCKS……………………………………..7 - INSTALLING THE ELASTICORDS…………………………………………….……..8...
IMPORTANT SAFETY INFORMATION Read all safety information before operating the MVP. It is the owner’s responsibility to ensure that users are aware of all warnings and precautions. Please read all instructions before using the product. These instructions were written to ensure the safety of the user and to protect the product.
Assembly of the MVP requires two people Keep in mind that the following images pertain to just one of the four available MVP models, your parts may appear slightly different than those in the included images but the required steps remain the same.
(Pic 1.2) 3. Insert the four 5/16” x 1 3/4” long button head bolts from outside the MVP rails and through the connector plate. 4. Hand tighten a 5/16” lock nut onto each bolt end on the inside of the connector plate.
18”. (Pic 2.1) 2. Place the head-end of the MVP rails to the inside of the head-end stand vertical tabs, and slide the stand forward until the holes of each structure are aligned. Once aligned, move the box to where the head-end stand can rest against it.
Once all eight bolts are in, place the 3/8” washers, then the lock nuts, onto the bolt ends and hand tighten. (Pic 3.2) 4. From the inside of the MVP rails, insert the 5/16”x 5/8” button head bolts into the top four parallel bolt holes (two on each side) and out through the kickplate structure.
1. Remove the two plastic rebound stop blocks from Parts Bag #4 and unscrew the lock nuts from the bolts. 2. With the bumper cones facing toward the head-end stand, insert the bolts of the plastic rebound blocks into the MVP rails and through the kickplate structure.
Parts Bag #5 7/16” Socket Wrench 1. Remove the elasticords from the box and place them on the floor between the MVP rails, on top of the connector plate. (Pic 5.1) 2. Facing the head-end stand, insert the loop-end of the red lanyards through the far right side 3/4” hole, inserting the dumbbell shaped lanyard mounting rod from Part Bag #5 through the red lanyard loop.
Page 12
ASSEMBLY OF THE MVP (STEP 5) INSTALLING THE ELASTICORDS STEP 5 Page 9...
ASSEMBLY OF THE MVP (STEP 6) INSTALLING THE HANDLEBARS STEP 6 ITEMS REQUIRED Parts Bag #6 Carriage 30” Long Handlebars 1. Turn the carriage upside down. Cut the zip-ties to remove the three, 30” long handlebars. Lift up on the retainer plate and slide the three handlebars through a side hold of the carriage, under the plate, and out through the corresponding hole on the other side.
(Pic 7.6) 6. From parts bag #7, insert the two knee bumpers into the bottom slot of the MVP rails near the head-end stand so they rest against the rubber cone.
Page 15
ASSEMBLY OF THE MVP (STEP 7) INSERTING THE CARRIAGE STEP 7 Page 12...
ASSEMBLY OF THE MVP (STEP 8) ATTACHING THE KICKPLATE BOARD STEP 8 ITEMS REQUIRED Kickplate Board 1. The kickplate board is adjustable to three different heights. Once the desired position is determined, insert the four protruding bolts at the back of the board into the desired corresponding holes of the kickplate structure. Secure the board by tightening the knurled knobs to the exposed bolts.
ASSEMBLY OF THE MVP (STEP 9) ATTACHING THE HEADREST STEP 9 ITEMS REQUIRED Bib Headrest 1. Align the Velcro strips on the back of the headrest with those on the carriage. With the pillow toward the head-end of the carriage, locate the desired position and press down and into place to ensure sufficient contact. (Pic 9.1)
ASSEMBLY OF THE MVP (STEP 10) ATTACHING THE BACKREST EXTENSION PAD STEP 10 ITEMS REQUIRED Backrest Extension Pad 1. The backrest extension pad can either be used as an extension of the padded center on the carriage (supports deep squats) or as an alternative low profile headrest (Pic 10.1). To use an extension, fit into the space at the foot-end of the carriage (Pic 10.2).
USING THE PRODUCT Located between the MVP rails are eight elasticords. They are at the head-end of the machine attached to the black and red lanyards. There are also eight additional elasticords attached to the foot-end of the carriage with t-handles.
- With the carriage flipped over apply silicone gel to the elasticords with gloves. 3. Lubricate elasticords located in the MVP rails (All models) - Apply silicone gel to the rubber portion of the MVP rail elasticords 4. Re-insert carriage into the MVP rails.
Page 21
MAINTENANCE (CONTINUED) Part #1510 - Universal Bib Style Headrest Complete with foam Part #1510A - Universal Bib Style Headrest Cover Only Part #3412 - Replacement Backrest Part #1436 - Kickplate Cover Replacement Replacing Backrest 1. Remove the headrest and the padded backrest extension from the carriage. 2.
SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. SHUTTLE SYSTEMS shall in no event be liable for death, injuries to persons or property or incidental, contingent, special or consequential damages arising from the use of our products. In administration of this warranty, SHUTTLE SYSTEMS may at its discretion request that the product or part must be returned for examination, postage prepaid, to our Bellingham facility.
- information about which parts are covered by the warranty and which must be paid for - supply of original spare parts. When you contact Shuttle Technical Support Service you must give the following information: - Product model - Serial number...
Page 24
Scan code to view our MVP YouTube Scan code to view our MVP Parts Playlist Page 19...
Need help?
Do you have a question about the MVP and is the answer not in the manual?
Questions and answers