Related Manuals for Racing RAC1836ECS
Summary of Contents for Racing RAC1836ECS
- Page 1 ORIGINAL INSTRUCTIONS=>EN ELECTRIC CHAINSAW RAC1836ECS USER GUIDE CAUTION: Read the instructions before using the machine!
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY WARNINGS 2. YOUR PRODUCT 3. ASSEMBLY 4. OPERATION 5. MAINTENANCE AND STORAGE 6. DISPOSAL 7. DECLARATION OF CONFORMITY 8. WARRANTY 9. PRODUCT FA ILURE 10. WARRANTY EXCLUSIONS... -
Page 3: Safety Warnings
1. SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 4 before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
- Page 5 CAUSES AND OPERATOR PREVENTION OF KICKBACK: Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and back towards the operator.
- Page 6 Use the product only under daylight or under good artificial light. When using the machine, always wear full protective equipment including a helmet, protective mask, ear protection, gloves, non-slip footwear and protective clothing. Wear appropriate clothing. Do not wear loose or unbuttoned shirts. Do not wear jewelry that may come in contact with moving parts.
- Page 7 Pay attention to foot and cutting injuries. Inspect and regularly service the product. Repairs should be carried out only by an authorized service center or a similar qualified specialist. When not in use, store the product out of the reach of children. ...
- Page 8 Even if you use this product in compliance with all safety requirements, the potential risks of injury and damage remain. The following hazards may arise from the structure and design of this product: There are harmful health consequences resulting from the emission of vibrations if the product is used for long periods of time or not properly managed and properly maintained.
-
Page 9: Your Product
5) Safety button 12) Hand guard (trigger for chain brake) 6) Rear handle 13) Protection cover 7) Supply cable 14) Tool for assembly TECHNICAL DATA Model RAC1836ECS 220V-240V˜ 50Hz Tension Power 1800W Max speed of the spindle 8000/min Cutting length 355mm(14”) -
Page 10: Assembly
Information: The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another; The declared vibration total value may also be used in a preliminary assessment of exposure. Warning: ... -
Page 11: Operation
Rotate the chain with your hand to check that it is turning without excessive resistance and that it is properly tightened. Repeat the installation if the chain is not tight. ADJUSTING THE CHAIN TENSION The tool motor must be switched off before adjusting the chain tension. Make sure that the chain is inside the groove of the guide. - Page 12 STARTING AND STOPPING Note: Ensure the brake is working efficiently. Check its operation every time before commencing work with it. Plug the tool to an extension cable. Plus then this extension to a socket outlet. You can put the cable on the cable holder(8) of the tool to hold it. Hold the tool with two hands, one on the rear handle, and one on the main handle.
- Page 13 2) Sharpening of the chain For best performance, we strongly recommend that you periodically sharpen the chain. The chain can either be sharpened by a professional or by yourself by providing you with a sharpening guide (make sure you know how to use it). The chain must be sharpened when: Wood chips have become powder To make a normal cut, force on the tool...
- Page 14 TRUNK ON THE GROUND Cut half of the trunk, turn it over and finish the cut on the other side. TRUNK IN ELEVATION Begin by cutting a first part from below and then from above. Then, on the second part, repeat this operation.
-
Page 15: Maintenance And Storage
5. MAINTENANCE AND STORAGE MAINTENANCE Before any maintenance work, the machine must be switched off and completely cooled. Perform the maintenance work according to the instructions below and perform them regularly. A clean, well-maintained machine increases its standard of living and efficiency. - Page 16 4) chain saw Check each time the cutter and cutting angles are as shown below. 5) Sharpening of the chain For best performance, we strongly recommend that you periodically sharpen the chain. The chain can either be sharpened by a professional or by yourself by providing you with a sharpening guide (make sure you know how to use it).
-
Page 17: Disposal
Declaration of conformity BUILDER SAS ZI, 32 rue Aristide Bergès – 31270 Cugnaux - France Declares that the machinery designated below: ELECTRIC CHAINSAW RAC1836ECS Serial number: 20220532058-20220532657 Complies with the provisions of the Directive "machinery" 2006/42/EC and regulations National transposing it;... -
Page 18: Warranty
8. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 19: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 20: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •... - Page 21 BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France Made in PRC 2022...