Advertisement
Quick Links
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
FEATURES
ADMW1001
programming device
Interfaces with
MeasureWare Lab
DEVELOPMENT KIT CONTENTS
EV-PRG-MW1001ARDZ
EQUIPMENT NEEDED
PC running Windows® 10
ST-Nucleo development board (ST-NUCLEO-F411RE)
SOFTWARE NEEDED
MeasureWare Lab
GENERAL DESCRIPTION
The EV-PRG-MW1001ARDZ is a firmware programming
board for the
ADMW1001
contains a flip cap socket for rapid programming of small volumes
of the ADMW1001.
swapping sequence to allow insertion and removal of the
ADMW1001
ICs before and after the programming procedure.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Arrow.com.
Downloaded from
EV-PRG-MW1001ARDZ Quick Start Guide
programming software
software
device. The EV-PRG-MW1001ARDZ
MeasureWare Lab
software controls a hot
EV-PRG-MW1001ARDZ
EV-PRG-MW1001ARDZ PHOTOGRAPH
The latest version of firmware is available on the
Lab
page, and enables new features and sensors connectivity.
For large volume programming of the ADMW1001, contact
Analog Devices, Inc.
For full specifications on the ADMW1001, see the
data sheet, which must be consulted in conjunction with this
user guide when using the EV-PRG-MW1001ARDZ.
Rev. 0 | Page 1 of 5
User Guide
UG-1664
Figure 1.
MeasureWare
ADMW1001
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Analog Devices EV-PRG-MW1001ARDZ
Summary of Contents for Analog Devices EV-PRG-MW1001ARDZ
- Page 1 ST-Nucleo development board (ST-NUCLEO-F411RE) SOFTWARE NEEDED MeasureWare Lab software Figure 1. GENERAL DESCRIPTION The EV-PRG-MW1001ARDZ is a firmware programming The latest version of firmware is available on the MeasureWare board for the ADMW1001 device. The EV-PRG-MW1001ARDZ page, and enables new features and sensors connectivity.
- Page 2 TABLE OF CONTENTS Features ....................1 Revision History ................2 Development Kit Contents .............. 1 EV-PRG-MW1001ARDZ Quick Start ..........3 Equipment Needed ................1 Evaluation Board Software ...............4 Software Needed ................1 Software Installation ..............4 ...
- Page 3 EV-PRG-MW1001ARDZ User Guide UG-1664 EV-PRG-MW1001ARDZ QUICK START To program the ADMW1001 IC with the EV-PRG- Place an ADMW1001 inside socket X1 on the EV- MW1001ARDZ, take the following steps: PRG_MW1001ARDZ and click Program in the MeasureWare Lab software. Do not remove the...
- Page 4 When the software is installed, navigate to Start > Programs > executable file available on the MeasureWare Lab webpage. Analog Devices > MeasureWare_Lab to execute the software Double-click the MeasureWareLab.exe file and follow the on program. screen instructions to install this file on the PC.
- Page 5 By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement.
Need help?
Do you have a question about the EV-PRG-MW1001ARDZ and is the answer not in the manual?
Questions and answers